Good afternoon,

I have two sensors that register always the same % of humidity. One, about 4/5% and the other about 98%.

For a test, yesterday I poured direct water in the sensor that indicate 4% and it jumped imediatelly to 95%, V but after a few minutes it returned down. Also during a small raining it didn’t change. Is there some suggestion to be function them right? Position, mode of positioning into che garden ….

Thanks 

Gianluca

I want o know when is best for the gras

Early in the morning? 6am etc...

Late in the night, 21, 22.h

Thx

Good afternoon,

Is it possibile to ad new site for the weather forecast? The ones available aren’t accurate.

Different zones have varying moisture levels even when I get rain. How do I adjust individual zone to have more accurate moisture level?

Hi friends, I have a doubt, how can I program my controller without the smart program? What I want is to schedule my lawn to be watered EVERY day at the same time: for example, every day at 8:00 a.m. for 15 minutes.
Thanks and best regards

I buy a new whisperer every year (on my 4th year now). I also try to charge the old ones each year. I set them in the direct sun. At night I put them under a direct indoor light source. This year they have been charging for a little over 4 weeks now. This gives them enough power to run for 7-10 seconds. As the watering season where I live is only about 4.5 months, this means that every whisperer only lasts me 4.5 months. It's a pretty expensive solution at this rate. 

Is my experience common? Has anyone gotten a whisperer to work after being stored over the winter (and I do charge then fully before turning them off for the winter)?  I assume the internal rechargeable batteries just aren't that good. Has any one had any experience changing the batteries?

The Sprite is breaking the watering of my trees into a whole bunch of short bits of watering. Given the way my soil sucks down water, I'd prefer to water my trees for 4 contiguous hours of watering every two weeks, but there does not seem to be a way do specify this directly.

Hi ,

I have a grass area that a split for 2 watering zones. How can I use 1 whisperer to serve both. 

How it possible to assign sensors to multiply zone or setup the zone to follow watering pattern of another zone. 

Ilya 

How long should it take to the senors to learn?

Hi there

I would like to learn more about the watering modes. Specially I would like to know the difference between EPA and Deep. 

Make´s sense to use it in summer? specially in hot areas over 30ºC

Thanks

Whisperer installed and working for over a month. Self learning completed and just getting great control of the watering. 

I have a weather station that is connected to WU. I have linked the station on the app, but it doesn’t seem to use actual rainfall. It only uses the forecast weather. 

How do I turn OFF the “All Day Smart Water Regulation”?  It is on for just 2 days a week and screws everything up.

Thanks for any help.

After 3 weeks of working, my whisperer stop working. It didn’t connect to the Wi-Fi. It was off.

I try to switch on, without any effect. I tried to put it direct indet the Sun for more then one hour. It restart working. After one day inserire the Sun it stopper again to work. Now is raining, so I can’t do nothing.

Ideas?

2 of my 3 zones are automatically watering however one zone is not any thoughts why?

Dear Netro,

I jut set up your device (again; because it is spring here); but smart watering time look way to much. Why do I need to water my 100 Sqm grass 5 times 8min in a day?

Thank you for your help in advance , Adrián 

My region is currently asking that we only water once per week. I was under the impression that the smart controller made those adjustments automatically for me, but it is showing that I am scheduled to water 3x this week. Is the only way for me to change this to do it manually? 

The moisture indicator in the app shows my soil moisture is 38% but we had 3 inches of rain on 24 hours. How is moisture determined? We aren't using any sensors

I created a schedule under settings, programs and indicated a start date. When I go to “schedule” I do not see the program j created on the calendar. Please help.