Hi,

I have 4 zones and a master valve. When I run any of the zones, they won't shut off when the timer runs out. If I switch the AC power off, then the valve will shut. I have checked the valve and it has no issue with opening and closing except when the sprite is running it. I tested cables for continuity, and I have tried swapping cables with no change. My ac power pack is AC 24v.

This issue affects each of the valves but only when controlled via the sprite. The valves are fully operational otherwise.

Hoping for a fix, otherwise will return to Amazon under warranty and get another brand.

My Netro controller is about three years old. I recently changed my Wi-Fi router about two months ago.  I repaired the controller with the new Wi-Fi, all seemed to work for a few days. Then the controller started cycling on and off of Wi-Fi. There are windows of several minutes that I can communicate with the controller, then windows of several hours when I cannot.  The light on the controller is solid for about 20 seconds, then three slow blinks, solid for 20 seconds, then three slow blanks, this pattern continues indefinitely. I have repaired the controller to WiFi several times. I have unplugged and then plugged the controller back in multiple times. Nothing seems to resolve the issue. It’s frustrating when I’m changing sprinkler heads and have to wait several hours to try a manual run to test the new heads. Has anyone else experience this and more importantly solved this issue? Thanks for the help!

Seems like my system has a mind of its own.  It'll water on time for a few weeks then stop then water again. 

My controller has been out almost a month. I have factory reset, short reset uninstalled app, and unplugged it. No matter what I do, i cannot get past the connect to netro wifi step. I need to blow out my sprinklers and I cannot get my device to work to manually run them. It will say its connected and do the spinning wait thing, then suddenly tell me to connect to the netro internet again. When I go to do it again it says no internet connection. Please help me. I sent an email from my email as the registered user (husband) is deployed in the middle east. Please look for an email from "kimbo__@" 

Thanks!

I have 6 zones and all but zone 1 run.  I start running manually and app says watering but nothing.  I checked the wires, none loose.  It will run randomly but I’m getting really frustrated.  

Hello there!

I'm really hoping you can help me. I bought two Whisperer 2s.

My sensor shows the moisture way above where I have my watering adjustment set to not water, but it is still watering. What am I doing wrong?

Hi everyone!

My Whisperer Smart Plant Sensor has broken. I would like to know if it is possible to fix it by buying a replacement part or if there is a DIY solution to reuse the device.

Thank you.

Desde hace unos días la APP no está funcionando. Según la APP el WiFi está OFFLINE, pero según la página web está ONLINE. Según ambos está WATERING pero la realidad es que no está regando y no responde a órdenes. No dispongo en este momento de acceso físico al dispositivo. ¿Podrían indicarme si el problema es un problema local o de la APP/Web?

For some time the system worked perfect. Now I  have two sections that don't work. It turns out that the signal to activate the valve is too short. When I  put a meter on it and then activate the valve the meter jumps to 28v for about one second then drops to zero before the valve can move. Conversely the one that works stays at 28v for much longer. I have rebooted and reset the system.  Any ideas?

I am doing yard work to 2 of my 3 zones right now and have the whole system disabled for several days as many heads are disconnected.  Woke up a 5am to have zone 3 on and spraying water everywhere for 20 minutes. 

How is this possible? Why do you not update your softwar? 

Ho, we need support, as we are having an issue as the app doesn’t activate watering. The control unot shows E1.

Quando collego la valvola la zona resta alimentata a 24 v anche quando finisce il ciclo. Quindi non smette di irrigare anche con la spia di colore verde.

Senza la valvola invece la tensione torna 0 volt.

Cosa può essere il problema

What can I do?

Thanks

None of the zones are watering when the app says it's watering. I measured each zone when active and each read 28 AC. When testing the resistance, the readings were jumping all over the place for each reading. This is leading me to believe there is an issue with the master solenoid valve. However, there is no wire that connects to the M slot on the controller. Looking around the house for any of the underground boxes, I have not been able to find the master solenoid. Attaching pictures of what I have found. Any help greatly appreciated.

One day, the Sprite just stopped opening the zone valves. We tested and reconnected all the wires and deleted and re-installed the Sprite. Still no luck. Ground is good too. What could be wrong?

En relación con mi pregunta anterior ya he visto que poniendo el riego nocturno a las 23:30 se acepta, pero si se pone a las 23:59 sale el error. Por lo tanto anulen mi anterior pregunta, aunque me resulta algo extraño que no permita 23:59 siendo el mismo día.

Saludos.

He instalado mi nuevo Netro Spark. En modo smart produce demasiados riegos en una determinada zona de forma muy constante, y con demasiado tiempo. No me parece nada lógico. Quiero dejar eliminado el modo smart y programar personalmente el riego. Consigo programar un riego de las cuatro zonas que utilizo en un determinado horario de la mañana, pero cuando voy a añadir un segundo riego diario por la noche me da un mensaje "ERROR: Program cannot cross a day".

¿Significa esto que solo puedo programar un riego al día? Muy extraño, mi anterior programador permitía tantos riegos diarios como quisiera simplemente indicando las horas.

Por favor, una solución, porque si solo se puede programar un riego al día no me soluciona nada este dispositivo.

Gracias.

Has anyone had only one zone not work properly? I've checked my voltages and everything seems to be normal but one of my 4 zones does not operate either with the schedule or manually running the zone. Any tips help cause i'm at a complete loss.

Thanks in advance

Boyce 

Hi 

I just restarted my irrigation system after the winter.  I have tried to manually run a zone.  After watering for 5-10 mins the water turns off but the Netro timer still shows watering.

I am trying to determine whether the pump has turned off because the Netro "on" signal stopped or whether the thermal overload relay on the pump circuit caused it to shut off.  

Is there a way I can check which it may be?

Thanks

Vardhan