There is a flow rate with a default option. Is there any value in calculating my actual flow rate? Will it just estimate run time better or will it actually impact the run time?  Or will it run indefinitely till it gets to 90%?

Thanks 

I see that my sprinklers keep repeating the watering cycling through the zones. I have ser it for manual run. However, once started I cannot stop it from cycling. So I have keep the system disabled and enable only when the watering is to be done. I also have to keep watching to shut it down when the last zone is done.

I do not see any setting that could cause this behavior.

There is any reason from the server side that I can get data using the API with the url using Chrome, but I get the message below trying to get the data using Node-Red?:

"RequestError: getaddrinfo EAI_AGAIN api.netrohome.com : https://api.netrohome.com/npa/v1/sensor_data.json?key=xxxxxxxxxxxx"

(xxxxxx is my the serial number)

I have to say that I successfully got the data using Node-Red with the first 5 or 10 petitions, but after that seems that I got a DNS block or permission denied using Node-Red, because if I use Chrome or Safari I'm able to get the data and the status OK.

Jose

The sensor is programmed to stay in green in the night, but shows red light. No update if changing in setup. Battery at 98%.

Seems to be working fine.

Hello. I configured the google assistant according to their document https://netrohome.com/shop/user_guides/4. It asks to link and takes me to a screen that says "try me" and it works perfectly with the instructions. If I close the phone when I go back in, it no longer recognizes instructions and I have to go through the whole process again. That's not how it works. Any solution? 

My model is spark 16

My problem is how each station is configured so that it stops watering when it rains and at the same time respects the times and days that I have in the program that I create. I don't want it to do smart watering, I want it to water according to my schedule and automatically stop watering when it rains. It's possible?

Hi - I am trying to determine if the 12 station Netro  spark would be easy for me to install.

I currently have a rather old rain bird system with 16 valves.

I think I understand the mapping of the com and individual values. But I am confused about the 24 vlt and my current rain sensor.

It seems like my 24vlt wires come from a pack/converter that is plugged into an outlet. Is this directly convertible - not sure how I take the orange wires and the devices they are connected to on the left of the picture to the new controller?

As well, would my current hunter rain sensor still work with the new controller, or do I need a different one?

Thanks for your help and advice.

Update:  in my original post below, I thought the problem was using the interval function set to three days. Since I posted that, I have also noticed that another zone which used the weekly function set to Monday and Friday also was not operating for the last several weeks. The one thing these all have in common is that the time was set for 60 minutes. Could there be a bug where if you set the zone to water a full 60 minutes, it doesn’t work at all?

Original post: I’ve been mostly satisfied with Netro for a few years now, but this is the first season I tried using the interval of “every three days.“ I started the setting last month in a few areas, and my plants were doing poorly. It took me this long to realize that it just simply isn’t watering them at all. That’s right, my programs are set up for every three days, and when I look at the schedule to determine when the last watering cycle was, they just haven’t been watered at all since I switched to the interval of three days. For now I’ve gone back to my weekly settings where I chose Monday, Wednesday and Friday, but am I the only one who can’t use the interval function?  I have dead plants because of this.

Yersterday evening Whisperer was active but today display is totally blank (only grey segments). 

No light on the device.

Everything else OK including weekly averages. The few days before becoming blank was a bit surprised by the readings. According to weather conditions and watering was expecting a rise in humidity but it was on the contrary shown as decreasing.

Is there a way I can re-start it or should I buy a new one ?

Thanks 

Was looking at the smart water schedule this AM and noticed an exclamation points next to several some start times. What does this mean?

Watering too frequently and not capturing moisture level. We received >1 inch of rain yesterday and says ground is less than 2%.  Schedules 30 minutes of watering each day for most zones.  Says it sound only be watering every 3 days for 23 minutes.  Something is not working correctly.

Kurt.connolly@gmail.com

Hi,

I did purchase Spark 8 in Canada but I will be using it in Spain. 

When I try to activete the unit, I cannot use my Spainish address for the location of the unit. The app is taking the location from my phone and when I put the Spanish address I get an error that I am located in Canada. When I turn off the location service of my phone I cannot move to the next step at all.

Any suggestions how I can solve this problem?

Thank you,

In the mobile application and in the web application I can check the history of the irrigation over a period of a year

I would like to know if you store data for more than a year and if it would be possible to export the data. For instance, last 3yr, 2yr

Thanks

Alfonso

When appears the yellow  sign I  have to start manually the irrigation.

Why doesn't it start automatically?

Now I'm abroad and I have to check daily...

Thank you

I set the smart schedule to go on at 50%. The app says if it goes below low, it will water till it gets to high

It’s set to a low of 50 and you can clearly see it let it get below low which it said it wouldn’t