What does it mean when a zone shows "--" under "Next in"?

It used to show 20 days until today..

I have installed Netro Sprite with no sensors (they are not available in Amazon Spain any more).

I have a few questions after my first day:

1. App shows different humidity values for each zone. Where does that info come from if I don't have any sensor?

2. When I click on a specific zone, I don't see any irrigation in the chart.

3. I have a 'fir tree' in my garden, but I haven't found it in the database. In any case, if I have a fir tree surrounded by grass, what should I configure to make sure that both the fir tree and grass are taken into account.

Buonasera,

ho impostato il sensore whisperer nel mio account come libero, non collegato alle due centraline.

Vorrei cancellare il sensore ma non riesco a farlo la voce rimane sempre presente nell’account e non esiste un tasto per eliminarlo.

I just bought a replacement controller for my old Hunter. All connections are done by color codes as per old controller and I see all zones in App but when I manually try to test each zone, only one of the 10-zones start. However, when I press STOP, it does not stop. What’s wrong in manual testing ?

 Isn’t there a simple way to remote trigger the device from the app without all the time constraints? It does not seem easy for me to, for example, turn on the device and let it run for three hours when I’m away from home and then turn it off remotely. I want to use this to hook up a fire suppression system.

Hi,

How can I change the start time for all the stations?

Thank you in advance, 

Franco

Hi,

I cannot log in Netro android app because my email is too long and it is not accepting all the characters. Please note that I do not have this problem with the IOS app.

 

Thanks

Hi 

I added my wife as a manager successfully but i don t know how i can let her see the device from her app. At the moment the she log in but the appis not connected to any device

Thanks

hi i have watering adjustment enabled based on water level on the whisperer. But is there a way to designate time for watering adjustment? Basically it comes on randomly when it senses that more moisture is needed but can be in the middle of the day when we're using the lawn. Regular watering times are already set to only do mornings and evenings...

Thanks,

Arthur

Buongiorno a tutti, 

Qualcuno può aiutarmi a capire se la centralina anche se offline e quindi non comandabile a distanza continuerà a irrigare quanto già pianificato automaticamente?? 

Purtroppo non posso andare prima di qualche giorno e ho paura che si secchi tutto... 

grazie mille 

Saluti 

Stefano 

I see that there is some ifttt integration but is it limited to control language and some data logging. What I would like to see is either an .ics subscription calendar or API access to post the next, scheduled water days by zone. It would have to be updated when the app updates and only needs to look out to the next scheduled watering day (start/end time would be helpful too). This would allow me to see when I need to move yard furniture, etc. 

Please add to suggestion/enhancement list.

Thank you. 

It would be great if you add an option for notifications once irrigation starts/finishes.Sometimes we need to start it manually and need to wait until one zone is completed to start the next one. A notification in the phone would avoid opening the application all the time to see if the current zone is completed. 

This is needed in the app. The scheduling is harder then it needs to be.

Good morning,

I ask you if in the next software update Netro the possibility of enabling and disabling the Master Valve for each zone, I explain, I have connected an Autoclave with a special 24 volt relay to the Master Valve output, there are areas where I have a system  micro-irrigation that does not need an autoclave.  

thank you

Andrea

Is there a way to see the battery status (devices that use batteries) in the app home screen? It would be of great use when one is leaving the home for a few days, to make sure the device will have enough charge for those days.

I have grape vines on a drip system that’s running at .5 gph. I need to leave the system on for 3 to 4 hours. Please change the app to allow for longer watering.

I’ve noticed what sunlight graph shows wrong value for the current day. This value is always higher than any other day but it gets corrected later. 

I’m watering grape vines on a .5 gallon drip system. I need more than 60 minutes. You made it too complicated. Just create an on off button with time increments

The Pixie timer is designed for automatic watering. However, occasionally you may still need to turn on/off the water manually. Before explaining manual watering from the app, it would be helpful to understand how the Pixie communicates with the Netro cloud server.

By default, your Pixie turns on its WiFi module once every hour to sync up with the server. The sync-up usually takes less than one minute. For the next 59 minutes the timer will be sleeping and disconnected from the WiFi until the next sync. When the timer is sleeping, it is unaware of the schedule changes, including the manual watering.

Therefore, when you start a manual run, the timer is most likely in sleep mode. It will have to wait until the next sync-up to start the watering. The waiting time will be less than 60 minutes. Take the following screenshot for example:

The current time is 5:24AM and the next sync is scheduled at 6:17AM. Therefore the waiting time is going to be 53 minutes. After you press the Start button, you can go to the Schedule page and the manual run at  6:17AM will appear on your calendar.