Only noriced it was on when there was onlt one minute left.

Now rhe manual operarion is somehow set at 45min and even if I chanfe it to one minute it goes back to 45. I worry it will go off in the middle of the night at unschedule time. 

Water is precious where i live. We havent had any rain since November. 

How can I stop the app to set schedule on its own for crazy amount of time?

Hi. Im a new user and everytning seems to be working ss it should but i get the following message when i check the server status

Hi,

Is it possible to upload data from the app so I can keep record on an externat file for more than a month ?

I would like to keep record for a year long. 

Thanks, 

David. 

Hi Netro,

One frustration I have is that manual run times are important to me but cannot be longer than 1 hour (or programs) and cannot be adjusted while running.

I have Netro connected to a solenoid that controls watering of our small vineyard.

I rarely water in any way other than manual, because I need to control the amount of watering and also use fertigation to feed the vines.

Due to the amount of water required, I need between two to three hours of watering. I also like to adjust as I go, depending on how long the fertigation takes, so the ability to increase time without stopping the watering is also important.

My other solution is to disconnect the wire from Netro and use a Shelly 1 instead, whereby I can turn the watering on and off as I desire.

I would rather just use the Netro app, given that everything is already connected.

It is quite limiting to not allow hours as well as minutes (or to allow more than 60 minutes). amd not to be able to increase (or decrease) the time while the manual run is going.

Hi,

We have a Netro Pixie that we have been using to water trees in our backyard.

We purchased two Whisperer 2 sensors to help understand how much to water.

We paired and installed one sensor which is linked to the Pixie.  This sensor works well and reports light, moisture and temperature and appears in the app in the zone watered by our Pixie.

The other sensor installed as "standalone".  This sensor does not show up on our app including in settings.

How do we access this "standalone" sensor or data?

thank you.

Hi guys, 

Is it possible to integrate nestro smart sprinkler to home assistant? 

Thx!

Hi there, Ive noticed that some of the pie-slices in the moisture/temperature/lux graphs from my Whisperer Plant Sensors are heavily coloured (darker) and some are lightly coloured (lighter). Is this supposed to indicate something? 

I suspected that maybe the difference in colour reflects upload as either live (or cached), but I double checked and they all have >50% wifi connection strength and report regularly...

Put Sprite in "paused" mode in winter 

To put Sprite in "paused" mode in winter, you will have winterize your system. First you will have to blow out the sprinkler. You can look at this video to find some useful information. 

https://www.youtube.com/watch?v=s3YRbJYmvgA&t=99s

This video mentioned that you will have to turn on the sprinkler, so you can use the instant manual run feature in the home page to manually start watering for each zone to make sure all the water is out of system.

Then you should put Sprite in "paused" mode just in case some one (for example the kids) accidentally starts a manually run from the app. To put Sprite in "paused" mode, you can go to the Home page->"Enabled". 

I am using Netro software with a Sprite-6 controller. After some moths use I am delighted with the system. The tools it provides help me a lot controlling my garden, with good results. Congratulations. Normaly I use three out of my four zones in Smart (advanced) mode, and the fourth one in Smart (Basic).

I would be useful if we could have a field (name it "Notes" or similar) so that we could enter useful information about the use of each individual program (for example, "I reduced frecuency to alternate days after Oct 15th", or other information. 

Not having that field causes useful feedback not to be available when managing programs.

Thank you.

Controller light is off and displays Offline status. Rebooted router resulting in WiFI connections elsewhere in my house and to my other devices except for the Sprite controller. Repowered Sprite controller and also did a reset— same status with no light and Offline status. Help!

Dear netro team

I have a  hub with more than 1 timers. But via the app it is only possible to manage 1 of the 2 timers. Is this a bug. So I can't explore the second timer timer and therefore I can also not get the data via API, because I can't see the MAC or Serial No. Can you please help here?

I solved the problem.

No consigo que la aplicación permita 2 zonas activas a la vez. Solo funciona de manera secuencial (Zona 1, luego Zona 2, luego Zona 3, etc).

Yo necesito activar 2 a la vez para regar y abonar al mismo tiempo.

Alguien tiene una solución por favor?

Hola, sería posible que en la programación, en la hora de inicio se pudiera elegir la hora y los minutos?

Gracias.

can somebody explain the two way of rain skipping. forecast and expection. I wanna know how it really worked 

Hello everyone,

Is it possible to set up more than 3 users in the user administration or are there plans to increase this number?

Best regards
WH