Hi.

I have a lawn that is irrigated by two solenoid valves, Zone 1 and Zone 2. Each zone controls 3 sprinklers, and there are overlapping areas between the sprinklers from both zones. I would like to configure the system so that when Zone 1 runs, Zone 2 also runs at the same time, and when Zone 1 is off, Zone 2 is also off. In other words, both zones should operate simultaneously to avoid certain areas always receiving extra water. Is there a way to set this up with the controller?

Hi, I have a Sprite 12 zones and a Whisperer 2 sensor added to the Netro app. However I cannot find any way to setup the sensor so that it inhibits watering if the measured humidity is higher than some value. The sensor is sending correct reading to the app but now it has been raining for few days and the Sprite keeps watering.

I would like to disable watering based on the sensor only and not on the weather forecast.

If in the app I select the Sprite, then go to settings>zones and select one zone i see the setting Sensor as "Not connected" but there is no way to connect a sensor. If i select the sensor and go to settings>sensor I see all the settings to change name, light color data send interval, but nothing about rain.

Can someone please help me? Thank you!

I've had a Netro Spark 8 working without any problems since last year, but a few days ago it disconnected from the Wi-Fi and stopped working. I tried the reset button as indicated in the instructions, but there's no way to reconnect it. What else can I do? Thank you very much

Buongiorno,

ho riscontrato un problema con la centralina Netro Sprite-6.
Il dispositivo risulta online e sembra funzionare regolarmente, tuttavia non attiva nessuna uscita: né la master né le due zone configurate. Ho provato ad attivare manualmente tutte le zone, ma senza successo.

Ho effettuato alcune verifiche:

• la tensione in uscita è sempre di circa 11 V AC su tutte le uscite;

• la centralina è stata utilizzata pochissimo, solo con le zone master e 1–2;

• non sono presenti segni visibili di bruciatura o danni hardware.

Da quanto riscontrato, sembrerebbe un problema software, poiché l’hardware appare in buone condizioni.

Resto in attesa di un vostro gentile riscontro e supporto.

Grazie per l’attenzione.

Cordiali saluti,
Giuseppe Sciurba

I have changed the name of my Wi-Fi. I need to change my Wi-Fi connection to its new name I have a new Wi-Fi in your hub will not work because it can’t download a new Wi-Fi for some damn reason

Just wondering if you can add a rain sensor to the Spark system?  If so what brand?  

Come faccio per poter attivare in una zona più elettrovalvola contemporaneamente??

For test purposes, I have my Whisperer 2 in a terra cotta flowerpot that is very dry.  It always reads that the moisture is very high.  I have a Pixie at the house faucet.  I reset the Whisperer and it did not help.  What's wrong?

Tried several times following with the instructions. And failed!? And my system was operational and my App was disabled for no apparent reasons!? 

I doubt if someone’s gonna break in and change my sprinkler time how in the hell do I save my password to this thing? I don’t wanna have to remember to put it in every time I want to change my sprinklers.

buongiorno è possibile sapere se sono previste le notifiche pusch pe la partenza e l'arrento del ciclo di irrigazione, se si come posso abilitarle.

grazie

Hi, I have a Spark controller. Where can I find in the app the rainfall forecast for next days?

In the home page I can see only humidity, temperature and wind but not rain in mm.

Thanks

Riccardo

I can't register my weather station ID in the Netro app. Can anyone help me? Thanks.

I have a home weather station that feeds data to https://www.wunderground.com/dashboard/pws/KCASANJO507?cm_ven=localwx_pwsdash

I have my sprite pointed at my specific weather station on wundergound.com. Today, my sprite claims I had 0.02" of rain, but my weather station detected none, and wunderground.com says I had no rain.

I have been noticing for a while that Netro was showing different rain data from what my weather station recorded, Netro usually records more rain than I actually got. I suspect this may be why my oranges are always under sized.

Somehow Netro is getting the wrong infromation from wunderground.com. Is there any way to fix this?

Is it possible to configure the irrigation time with seconds? or should it always be minutes?

Hi, 

any update on the "greenhouse" options which would not count on with the rain, wind and probably increase the temperature for the selected zone?

Thanks!

I have changed the name of my Wi-Fi. I need to change my Wi-Fi connection to its new name I have a new Wi-Fi in your hub will not work because it can’t download a new Wi-Fi for some damn reason

It would be nice to receive an alert when the whisperers are running out of battery 

Todos los sensores que he adquirido al cabo de dos años dejan de cargarse por el panel solar y son inservibles

Conectados por usb a una fuente de alimentación son capaz de emparejarse pero al desconectarse dejan de funcionar 

Enchufados a la corriente la luz única un bucle de rojo de menos a más parpadeo amarillo y parpadeo verde. Los puedo dejar cargando por usb 12 horas pero al desconectarlo se mueren

Alguna solución ? 

My password keeps dropping, and I have to re-enter the password every time I want to use my phone to access programs.