Why is battery status 282% of charge. Can’t go over 100%.

Hi there,

Is there an option to set a manual run or a one time run for more than 60 minutes? I would like to perform a deep soak on some of my older trees. The smart schedules will only run water less than an hour as well. Is there an explanation why zones will not run for more than an hour? 

Thanks

Hello,

I have a problem when I checked the server status. The app says that the port MQTT is blocked.

Can you help me please?

Thankyou

I want to set up a repeating program schedule to run every 4 hours to establish a new lawn. At this point I have found the repeating programs will only allow a minimum interval of 1day (24hrs). Is there a way to schedule a repeating program with a shorter interval time? 

Vorrei usare un altra app meteo come si può collegare 

I’ve read that night watering is not good so why does the device order a watering cycle after 9pm?  Smart watering is enabled on all zones. 

I have declared drippers. How does netro calculate watering mm? Does it not dépend from drippers sizes?

Thanks

JM

Hello,

I am using one Netro Pixie Hose timer to water 2 freestanding planters via a hose splitter.  I am looking for a way to add 2 Whisperers to the Netro App to monitor both planters for watering needs.  The app appears to only allow one per zone.  Is it possible to add a second Whisperer to the same zone?  I am not concerned about overwatering as the planters allow for extra water to drain out easily.   I just want to make sure neither planter dries out.

Thanks

Hello, I have 3 pixies installed,  two of them are separated 10cm from each other, so they are in same place, but one of them is most of the time offline... what can I do??

Today has rain a lot and the pixie has been watering for more than 1.5h... that's a lot of water waste. 

Please give me a hand how to solve this. 

Thanks 

Luis

In the past week watered alternatively once a day and twice a day for all zones.

In Discover the irrigation cbm are stuck at 0.01 and worse show 0 for the last few days.

iPhone -

- Get app

- Crete account

- Go to connect timer

- Next

- Enter name and stuff, next

- Turn on unit, next

- Connect to Netro_* wifi, next

"Please connect to wifi network "Netro_*"......

I have disabled the IP security on the iPhone side. 

Please advise.

Good morning,

Randomly my device loses connection and keeps blinking.  I have to turn it off and on for it to get the network back.  The Sprite is five meters from the router and next to other devices that have a good connection at all times.

Thanks 

I'm not sure what Netro did to the App over the winter but it does not function worth a damn. We turn on one zone manually and shut it off and try and turn on another zone and the first zone state is also on. 

One of our customers has a problem where all zones come on a one time.

Bring back the last version!!!

I just installed the pixie timer and i would like to test it. 

However even if i scheduled two test runs, none of them appears in the schedule yet.  Is the schedule updated only once a day? 

Manual run is not available (the timer appears strike-out) so i cannot even test that way.

Thanks in advance for your help

Best 

 Jacopo

On my schedule screen sometimes I have an “!” mark. Sometimes it’s a “i” If I tap on the zone it takes me to preferences. Did I make a change that I am not aware of? What does this mean?  Thanks. 

Hello,

I’m trying to setup schedule for watering for next five months, But watering schedule shows only for two next months. I check the settings and I do have a selected five next month. is there something I’m not doing right?

Hello,

I can only add a maximum of 3 zones to my Whisperer Sensor. I wanted to add all my 6 zones to it? Is that possible? 

Thanks