I have 2 houses and I wanted if it is possible, with a single phone to control 2 Netro
Cordially

Recientemente instale tres sensores junto a  él programador Netro, pero los sensores no indican ni horas de luz ni humedad, en la app 

¿cuantos días están en modo aprendizaje? 

Muchas gracias  

For new seeding i need possibility to run every zone every hour for 5 minutes…

Smart watering is over watering the yard

I am trying ro add a new device but when i connect to the device wifi so i can configure it the app logs out and i have to switch back. So stuck in a loop unable to add the device

Does anyone know why the Dark Sky weather service was removed and replaced with Netro Weather.  My system has work great until today.  All six zones ran this morning and we had roughly an inch of rain yesterday.  Never had this issue with Dark Sky.  

Hello,

I have a big problem with my pixie, since I bought them. I have them connected into the app, but when I open the tap they never cut the water, the irrigation is on all the time.  

Do anyone knows where is the problem?

Thanks

Just booted a pair of Pixies for the coming grow season having recharged the packs via USB.  One unit is fine, the other booted one then shutdown and is dead.  I swapped the batteries around and the problem followed the the battery.   I don't see a replacement battery pack on the store so how do I get this replaced?   Pixies got bought last year.  

hi

manual app do not start watering 

no push button 

How do I change the frequency of days watered and the amount of minutes watered for each zone.

Also, I cannot find manual run on my ipad.

How do I add a zone

Is there a way that Netro can allow 30 second waterings? This would allow Netro to be compatible with some of the tower gardens that use soil and have internal irrigation systems. 

Is anyone else having a hard time getting this thing to work? I purchased a Pixie to automate watering my tomato plants in a small garden bed, but so far it's been beyond frustrating.

The app either shows the Pixie on standby or offline,but it's clearly communicating with it... if I pull down to refresh, the green light on the Pixie starts to blink.

However, I just can't the Pixie to actually work as a timer. I set up a program with a watering schedule, but the Pixie doesn't listen to it, and it doesn't show up in the calendar. When I try to start manual watering through the app, the time is crossed out, and pressing play / start does nothing whatsoever.

The home screen is also super unhelpful and shows no past or scheduled watering times. The only way I have been able to get the Pixie to water is to walk up to the unit and press the button twice... but the app doesn't register those either.

What am I missing? Unfortunately, the Pixie manual doeant explain the app at all. Is there a new user guide somewhere that I haven't found?

Honestly, I haven't been as frustrated with a piece of tech in a long time, and am about to return it if I can't find a solution in the next few days.

What is the easiest way to test run an individual sprinkler circuit with a Netro Sprite controller?

The large male/female end of the Pixie cracked again after one season. Last time I had to buy an entire new one. Anyone make the custom looking part?

May I reconfigure localization of my Netro Spark without reset the device? I have configured the device at home and now installed at my summer house many miles far away. Thanks.

Hi,

How do I set zone size for lawn areas sprinklers that overlap one and other?  For example, I have 6 zones, and in the front Zone 1 and Zone 2 overlap the areas they water in some cases.  So, in my case if the area covered by both zones is a total of 1000 feet, do I set each zone for 500 feet or each zone for 1000 feet.  Thanks.

I find the most of the time when I do a manual run, the station select get stuck on communicating….  I keep trying over a period of time and eventually one of the times I hit the Play button it goes straight to Watering and the manual run is successful.

I had to replace a Pixie and cannot add a sensor to the area of garden it irrigates. The Timer->Settings->Sensor contains no add button.    Android 12 on a Samsung S21, App version 3.0.1

What am I missing?