Need to change the rainfall for the prior day, how do I do it? 

Da qualche giorno il dispositivo ha smesso di funzionare. Non irriga né manualmente né con il programma. Ho già provato a rimuoverlo dall’app e resettarlo, ma non è cambiato nulla. Cosa consigliate di fare? Grazie

Please

I have had smart cotroller netro for 3 years. Never problems! 

Now i d like to buy z1 pixie with hub! But is it essential the hub for smart controlling? And if yes the hub has to be connected by lan to the router? 

Salve, quanto deve risultare l’umidità del terreno in giardino? Il sensore mi indica sempre tra i 96 e 97%. 

Hello, I have 5 sprite-type irrigation controller units installed. In one of them, the irrigation stops after approximately 14 seconds on all channels, although it still appears as watering in the status. We have measured the electrical resistance and it is normal.

Why do my zones only activate for 2 seconds?

I have one sensor that is controlling 5 zones, in the last few months it has rained for several days and the humidity recorded has always been 100%. For three weeks however it has not rained anymore and the soil has started to dry out and so has the garden, because the sensor continues to report 100% humidity skipping the irrigation cycle. How can I unlock the sensor humidity reading?

Could you add a pause feature in Manual run? When I am running a zone, sometimes I need to halt the run and make an adjustment or fix a leak and then turn it back on. Right now, I have to stop the manual run and then start all over. 

My indicator led is burn out. whocan I replace it?

Hello, I have activated Continuous Monitoring on my Wispering gen2 which means I should get an emediate update when the moister has changed.

But I don't get any update/ change until the aut hourly upate of the measurement is done.

I have installed a new Sprite - however, I have 3 common wires but only two slots - and only one wire fits in each slot...

Sprite-12

I want to utilize automated rain delay feature.

If I have my 11 zones enabled for Smart Zone watering, the zones will water in a random order.

I need them to remaian in order 1-11. I cannot yet find a readon why.

Not much fun sitting on my lawn when a zone unexpectedly turns on.

If I use a manual program, then the rain delay feature cannot be used.

Is there a way to enable an automated rain delay in a manual program?

and/or

run the zones in an order when utilizing the Smart Zones?

And yes, most of my zones have the same environment settings

Hi there I use the netro smart feature and the whisperer. 

The smart schedule for zone 5 watered 28 minutes at 5am and the sensor measured 99% humidity.  Then it watered again at 6am... which is obviously a waste of water as the zone is already 100% humid. So it look like when the program starts it does not take into account the humidity again until the next run for that zone. 

For zone 5 I am using regular mode. Not the Deep or EPA. 

I also have the condition that 

- Sensor to report every hour

- skip watering if above 60%

- Sensor firmware 2.0.1

Can I send my controller in to get it repaired? 

Dear Fellows,

I will be away for over a month and want to confirm the best practices to ensure my Netro Stream batter operates reliably throughout this period. Could you provide tailored recommendations based on my device’s current configuration and usage?

Device Details:

• Hardware : Netro Stream 1.0
• Firmware: 1.0.0

Please advise on any critical steps I might have overlooked. I aim to finalize my plans.

Thank you for your assistance!

Best regards,
Kelvin

Hi

Suggestion:

It would be great if it was possible to have a better overview in the Netro app when using multiple controllers. 

For instance, we have 2x Spike 6 zone controllers and 1x Pixie in our setup and it's currently tricky to have a overview over all zones scheduled in these controllers without switching back and forth between them. If only Schedule tab would list all our zones setup in all our controllers :-)

I have a digital water metering in my house from my water supplier. So know the exact amount of water that ist running for all zones If netro ist running and watering the Garden. Unfortenately i can Not find an Option, to Tell netro how much water in qm per hour is running for wach zone. IT would be great If that could be implementated to have an exact number of qm water that ist uswd for watering each zone. So gar I know netro gives only an wstamated number of water used for wach zone, depwnding in size of watering area and Type of watering equipment.

Help for my controller dropping the wifi weekly?  I have to unplug the controller to reset and wifi works.  When on vacation my controller can't be unplugged so is there a fix or work around ?

I can't connect both of my two Pixie devices to Alexa — I can only control one.
How can I fix this issue?

Thank you.

Perché nonostante l umidità rilevata dal sensore sia superiore alla soglia impostata, la centralina programma delle irrigazioni?