Hi,

My Whisperer 1 doesn’t show any signs of life after two weeks in bright sunlight.

I’m pretty sure the battery or charging circuit is dead after no use for over a year.

Do you offer a repair service or replacement battery?

Regards,

Andy Fiore

I have 2 zone in full sun with hydrangea and Japanese maples. I need to increase the length of watering time on the automatic watering cycle and the frequency

Hello,

I get this error only on a couple of zones.  See the attached photo. As you can see the zone "misc" shows error.  Any ideas 

I have a Netto controller 12 

It starts the water pump but not opening any valve 

It would be great if for someone like me there would be an option that unifies multiple controllers into just one home so that scheduling would be much easier and avoids multiple zones of different controllers run at the same time. When programming controllers in fact, I have to keep switching programming in various controllers to see if that time is not taken by another zone of another controller. Otherwise water pressure would be a problem if two or more zone are running at the same time in different controllers. 

Hi everyone,

I tried to conect 24v and 9v  valve to ny Netro 6 zone system. It seems dont work... I heard a noise near evry valve when turnd on (on manual mode) but water doesn't com up... Just a 9v valve can open just for few second... Water comes up... But after this tine... Water stop to come.

In the pictures show a 2 model used (24 and 9v)

Thanks to every can help me

We have 3 controllers for over 24 zones. 

Dark mode and font size (especially a problem with charts) are two things that were going to be addressed a few years ago. Could I please get a current status on when dark mode will be available and when font size, or at least the ability to zoom the app screen will be available? Turning on the Apple magnifier, or having to take a screenshot and then zoom that so that you can read data is very inconvenient. 

Question in subject title

Good morning,

I have my netro sprite with green light showing connected.

Nonetheless, when executing the programs it shows "connection problems". When I try to run the programs manually, it keeps "connecting..." but does not open the valves so that it waters.

I have removed and reset the connection with the network, it becomes green again, but it still not work.

I have also reviewed the electrical connections on the valves, and they are ok.

I have also tested opening the valves manually, they open and water normally.

the only problem is when executing electronically... it keeps "connecting...." and does nothing.

Thanks for your support!

I have three zones with Whisperer 2 devices that have been installed for some time. It to skip watering above 90% and water extra at 60%. Soil moisture is currently at 56% and to says it isn't going to wTer again for like 40 hours. What's up with that? There is only a 38% chance of rain, and that is .1 inches so that can't be it.

Hi 

I have some basic programs to water.  At the same time smartwater is enabled on zones?  

It seems the programs run - but smart water does not control the duration 

Is there a way to specify when watering evens should start but let the smart water control duration?

I am limited in GPM, and in some areas of my lawn, I would like to water for more than 1 hour at a time for deep soaking. I cannot find a way without using multiple programs to the same zone. It is pretty labor intensive.

My #1 zone comes on whenever any other zone is on.  There has been no changes since last season other than a new wifi gateway.  I have deleted the Netro app and still have the same problems.  I have checked wiring to the controller and it is exactly the same as last season.  No shorting.  Does anyone have another suggestion to try and solve this issue?

Any reason why the system sometimes skip zones and not water them. I have 3 sensors and they all reading the same moisture across all 9 zones, that’s why I’m confuse into why sometimes decide to skip zones. 

Does anyone have ideas for protecting whisperer from my gsd puppy?

My whisperer-2, installed ~36 hours ago, is consistently reporting a temp about 10F hotter than reality.

Thoughts?

Having problems getting it to connect to wifi?  Trying everything I can think of? Help???

I have 3 Whisper gen 2 sensors 2 have firmware 3.1.1 and one has firmware 3.1.5. How do I update the firmware on these devices?

Dear Netro Support Team,

I hope this message finds you well.

I am writing to inquire about purchasing a replacement battery for my Netro device, which has recently stopped working due to battery failure. Could you please provide information on how I can order a replacement, including the price, availability, and shipping options?

The model I am using is PIXE, and I would appreciate any assistance or recommendations you can provide.

Thank you for your support, and I look forward to your response.

Best regards,

Minh Thu, Nguyen