I had previously installed a Whisperer sensor and then removed it from the app.  I factory reset the Whisperer 3x successfully.  When I try to re-install it again, I go through the setup process and at the end, I receive a "Sensor xxxx already in your account".  I have gone to the app and website to see if the sensor is listed but it is not.  Any suggestions on how to fix this issue would be sincerely appreciated.

HI Support Team and All,

I purchased the smart valve (PIXIE-1)  and the sensor (WHISPERER-2) for my vegetable garden, but unfortunately the pixie-1 releases a few drops of water when it is in irrigation mode, my watering system is ecological, I collect rainwater, 

because the pixie-1 does not it passes water with little pressure, the pressure is low but sufficient for irrigation.

This wasn't written anywhere.

Is it possible to configure the valve to use it with low pressure?
thank you all

Leandro

I’m currently using my Netro spark 16 to water a 1 1/2 acre field of grass. There are a couple zones that are repeatedly watering for just a few seconds or a couple minutes when they are supposed to be watering for 6 to 10 minutes. It is causing a very big issue in the field. There are a large bare spots that are directly around the problematic zones. Is there any fix to this? I need answers ASAP.

Hi, 

Netro will water my garten when the Whisperer sensors show 92% moisture level. 

This is smart watering? 

I think, there is no water needed or I’m wrong?

How do I turn off smarr wartering?

Hallo and short question: 

I can not find any option to water more than one zone in the same time. Ist this not possible? 

@Netro team: in case the feature is not available at the moment i would appreciate your development 

Need manual run to be immediate... obviously. What prevents this?how to overcome.akes trouble shooting horrible 

Whisperer stake cracked when lawnmower hit it. Can it be fixed?

Is there a way to manually adjust the soil moisture levels? For example, I have a zone that is reading as saturated (above 80). However the irrigation in that zone has not been connected prior. It would be useful in the app to be have the user adjust soil moisture levels manually to help with issues like this in the future. I do not have any soil moisture probes installed so the moisture levels are being automaticaly calculated by the smart watering algorithm. 

Hello I have two questions that I hope someone can help with.

First.

I have my schedule set to skip Rain on Previous Day, Rainy Day, Next Day. It just rained for two days here locally and the system still kicked on today. Am I missing a setting?

Second.

When I set my schedule it will only populate for the current month even though I set the program I have for 5 months. Am I missing a setting?

Thank you. 

I replaced the router, the extender remained unchanged.  Unfortunately I am unable to reconnect the 6-channel control panel.  It's like it doesn't reset.  After the reset the LED remains off.  The wifi network is present, but it gives me an error when connecting after entering the password.  How to solve 🙏 

in the SMART Advanced zones section of the APP in the SI system the mm/hour scale goes from 10 to 100
in the US system Cubic inch per hour [in³/h] from 0.1 to 5

the data refers to the single zone therefore VALVE in my case PIXIE 1. 

The scale of values used does not seem to be correct a 3/4 hose with a pressure of 1 Bar brings about 9000 liters per hour 

perhaps the data in the app and mm³/seconds and in³/second I'm doing something wrong.
Thanks for the reply

Leandro

Is there a way to leave a sprinkler valve open all the time? I don't want to make a schedule. I have a valve connected to a motion activated sprinkler. I need that valve open all the time.

Thank you in advance

David

i 

How can I reconnect to Wi-Fi

the controller light is green
I have disconnected it from the network and plugged it back in but it doesn't work
Please i need help

My original netro spark died and I have received a new one.  Is there a way to copy the zone settings from the old to the new

can somebody explain the two way of rain skipping. forecast and expection. I wanna know how it really worked 

Hello everybody, maybe someone can help. 

This morning I found the irrigation system on, watering the garden, with no schedule active. More, the master enable/disable switch on the app homepage was set to off.

I'm using manual zone scheduling, not smart watering.

The controller is a Netro Sprite 6 zones, Wifi was on and fully functional. 

Any ideas? Thanks.

Claudio

Hola, sería posible que en la programación, en la hora de inicio se pudiera elegir la hora y los minutos?

Gracias.

How do I clear out the schedule and start over. 

Can a Whisperer be assigned a Sprite zone, and the Sprite use Whisperer's data to optimize the watering schedule?