help just getting this set up. came with my house. the light is not blinking. can’t find a start button

What is the default setting for not watering the day before and after a rain day? I think it was to skip the day before and of, but not the day after (wish I could reset defaults). Why is the default what it is?

Also, why is the rain delay trigger 0.2? What would happen if I changed it to 0.1?

hi, which setting is recommended for irrigating hedges?

Hi,

My netro has been working fine for the past many months.

Suddenly it stopped working and light blinks.

I try to configure the Wifi again and it states 

I am sure my 2.4 GHz network is available there as I have 2 other devices 10 Cm away from the netro and are working fine at 2.4GHz

I can confirm that in my Orbi Router.

Any ideas ?

Thank you

Carlos 

Is it possible to link an activity such as a scheduled zone watering to switch a specific smart light? I have 6 smart lights in my kitchen and would love if they where linked to my 6 watering zones. 

Hello All, I have three zones and created a program to do a deep water for 20 min. Starting from 5AM and ending at 6AM which is expected to run every 3 days. This morning was the first time I ran it and noticed on my home screen it said watered for 5 min. Any reason why this changed? I'm thinking smart watering has to do with this? If so, I'd like to try and keep this feature for the rain aspect (not to run when it will rain). I read if you disable smart watering (which I can't find this feature anymore), then it will still run the  program when it rains,anyway if I'm in the right ballpark to have your cake and eat it too. 

Thanks in advance

Hi

Had to replace a solenoid on the valve on one of my 2 zones and when I do a manual 5min watering on zones 1 or 2 none of them start. I can hear the click of the main valve opening but none  of the zone 1 or 2 valves is opening...if I use the override on the valve to open manually, the water does pass...seem the controller is not sending any open command to eather solenoid of zone 1 or 2 ..

Thanks for your help :)

Hi there,

I recently installed the Pixie, and have set up both the smart feature and a regular watering program. The watering program was supposed to go off this evening, but it didn’t. I then checked in the schedule, and all I saw were any restrictions and the smart watering schedule. My program was not there. I set the filters to show me the enables program, but it still does not appear. I have no way of telling with the program has been initialized. Is this a glitch? Should the program appear on the schedule? Why did it not activate when it was supposed to?

Thanks.

Hello, i have a netro sprite with 6 zone, i need controlate when i watering zone 4 (example) on sprite... open the pixie too. It is possible ?

Thanks you Sebastian

I replaced my Rainmachine with a Netro but I cannot configure it to do what the Rainmachine did. I live in Austin And can only water 1 day a week. Water is incredible expensive so I  cannot use Smarzone because my water bill will be too high. I want to run each zone for 20 min once per week and not water when rain is expected or it is raining. Netro does seem to be able to do this. Any suggestions?

Hi, 

I have a bed garden with multiple types of vegetables. My irritation type is drop emitter and I bought the humidity sensor Whispered and Pixie.  My garden surface is 100 square feets

I wan to know what is the best app settings to have the best results. The app contains lots of settings and I am little confuse!

thanks

Hello,

I to plan buy Netro Sprite splinkler controller. But I need know if I need pay any fees for using Netro app. Because the app using account at netrohome.com websuite.

Many thanks for early answer

Best Regards
Roman

I understand that Netro estimates water usage based on time, emitter type,  and square footage,  but I  have access to actual flow rate via a Flume flow rate monitor. Is there a way to replace the flow rate estimates with actual rates for each system? 

I do enjoy my Netro, and the app makes things pretty handy.  I do have a couple of questions.

Are there any plans to allow the software to rearrange the zones in a watering cycle (or is that already available and I am just missing it?)  Right now it seems I am stuck watering in the order I have wired the controller.  It would be nice to water one zone, let that soak in while watering another zone, then come back and water a third zone that is adjacent to the first zone.

Another question I have is - is it possible to copy a schedule so that I do not have to set each of the 5 zones for every schedule.  There are times when I would like to run a one time schedule that follows my normal dry schedule,  or follows my moister schedule.

Hi

I use Netafin pressure compensated drip hose on all my beds and there doesn’t seem To be an irrigation type for that. Is it OK using the drip setting which seems to be for micro drippers. 

Thanks

I'm evaluating whether to by a Netro and one of the things I need is to be able to name zones rather than have a zone called say "Zone 6".

I don't see any users manual on your site to answer questions like this.

If wifi is disrupted will the controller continue to water acording to the most recently programmed schedules?

More generally are there any modes of failure (other than loss of power to the house) where the controller can unexpectedly halt watering?  It would be unacceptable to have one's garden die from lack of water if the system fails when one is away from home for a number of days.

Sensor 2 says moisture level is 7% after very heavy rain, but the weekly view says 92% 

Hi, sorry but is there the possibility of a web interface, without using the Netro app?

Can a pump delay be programmed between zones?

Thanks