Can you please set my pws to KNYFORTS6?

Thank you. 

Hello,

In my settings the watering time is set from 2:00 to 6:00 in the morning.

The system shows in the watering plan that some zones will start after 6:00 oclock. 

This needs to be fixed because of a mowing robot wich would drive against the irrigation system

Hi

Please can you add the following weather station to weather underground: ILONDO539

Thankyou 

Manual operation of zones used to work, but not longer does. Sprinklers operate as desired although when I select manual operation/play, they say they are on, although never turn on, please help resolve this. 

Hi

program error.  In the Android version, the water consumption data in the weekly history is offset by one day and, moreover, the last day does not appear.

Hi there, 

I'm noticing a very large difference (greater than 5 degrees) in the temperatures forcasted  provided by NetroWeather. Maybe my region isn't covered or forcasted accurately by the netro weather service. I didn't know if I am only experiecing this issue or if it is more widespread. Why is the recommendation 5 stars? 

Hi

I know this issue already got mentioned by other users over a year ago, but I would like to ask again for fixing this bug. I know that on a technical level fixing this will take only a few minutes. 

To my understanding the main valves is intended to avoid constant water pressure on the system. Unfortunately the closing sequence is mixed up and the main valve closes a second or two after the last watering valve closes. This means that there's contant water pressure on the system. At the moment I would need to manually open one of the valves three times a day to release the pressure (at 5:30AM, at 10AM and at 17PM). This is not exactly what I expect from a smart watering system. 

Just yesterday I had to replace a part of my systems because it broke due to the constant pressure. 

I know it's tempting to point at everybody else in order to refuse acknowledging that there is an important improvement to be made. But fixing this will probably cost less time than I used to write this text, seriously!

And while in my case it wasn't a Desaster because I was lucky that the pipe connection broke during manual activation of a watering program. But in other cases, if this happens without getting noticed, this could easily destroy a whole greenhouse of commercial food production.

That said, please fix this minor but important bug ASAP.

I really can't believe that you guys simply ignored the previous reports of this bug. But I hope you do the necessary steps to initiate the fixing of this bug.

Regards 

Has anyone faced this problem in their garden?

Regards!

There is a flow rate with a default option. Is there any value in calculating my actual flow rate? Will it just estimate run time better or will it actually impact the run time?  Or will it run indefinitely till it gets to 90%?

Thanks 

I see that my sprinklers keep repeating the watering cycling through the zones. I have ser it for manual run. However, once started I cannot stop it from cycling. So I have keep the system disabled and enable only when the watering is to be done. I also have to keep watching to shut it down when the last zone is done.

I do not see any setting that could cause this behavior.

There is any reason from the server side that I can get data using the API with the url using Chrome, but I get the message below trying to get the data using Node-Red?:

"RequestError: getaddrinfo EAI_AGAIN api.netrohome.com : https://api.netrohome.com/npa/v1/sensor_data.json?key=xxxxxxxxxxxx"

(xxxxxx is my the serial number)

I have to say that I successfully got the data using Node-Red with the first 5 or 10 petitions, but after that seems that I got a DNS block or permission denied using Node-Red, because if I use Chrome or Safari I'm able to get the data and the status OK.

Jose

The sensor is programmed to stay in green in the night, but shows red light. No update if changing in setup. Battery at 98%.

Seems to be working fine.

Hello. I configured the google assistant according to their document https://netrohome.com/shop/user_guides/4. It asks to link and takes me to a screen that says "try me" and it works perfectly with the instructions. If I close the phone when I go back in, it no longer recognizes instructions and I have to go through the whole process again. That's not how it works. Any solution? 

My model is spark 16

My problem is how each station is configured so that it stops watering when it rains and at the same time respects the times and days that I have in the program that I create. I don't want it to do smart watering, I want it to water according to my schedule and automatically stop watering when it rains. It's possible?

Hi - I am trying to determine if the 12 station Netro  spark would be easy for me to install.

I currently have a rather old rain bird system with 16 valves.

I think I understand the mapping of the com and individual values. But I am confused about the 24 vlt and my current rain sensor.

It seems like my 24vlt wires come from a pack/converter that is plugged into an outlet. Is this directly convertible - not sure how I take the orange wires and the devices they are connected to on the left of the picture to the new controller?

As well, would my current hunter rain sensor still work with the new controller, or do I need a different one?

Thanks for your help and advice.