I have a whisperer and a pixie configured in the same zone. My pixie is defective (the unit leaks water which wound up damaging the unit and battery and no longer works, replacement is in progress), so I want to delete it in preparation for my replacement. It says I need to remove the sensor first. Is there any way to just move the sensor (a Whisperer) to a different zone, or perhaps to just simply unlink the sensor from the Pixie, or do I actually have to delete the sensor from my account and then go through the process of re-adding it back to my wifi network and all that? The app makes it seem like I have to actually delete it then re-add it. Since my replacement unit won't be here for over a week I had desired to keep the sensor monitoring the soil in case I need to manually water it.

I'm only using a sprinkler system to water St. Augustine grass on a .2 acres in South Florida. The entire area is flat and has the same soil make-up (loam). Direct sunlight shines mostly all day on every area other than a small 10'x40' strip on the west side of the house that is shaded part of the day. I have no trees and no plants. I have a Sprite controller and 1 whisperer sensor which is connected to the 3 zones that get the most sunlight. The learned % is at 55%

I don't see any benefit in using the whisperer. Thoughts?

It's annoying that text overlap in the app. It's there a fix for this?

I have all connected and seems fine but when testing turning on each station I get a "pending" but no sction!

Each zone then said"loading"  for 5 minutes each then nothing. Please offer any help!

My phone will not connect to the Sprite, any suggestions?  It tells me to connect to Netro….., I select that in my WiFi options, but it does not connect.  

I have one Whisperer up and running just fine. Based on this I purchased a second. The second produced readings that were inconsistent when the device was placed next to the first Whisperer (read about half on moisture when compared to the first). So, I sent it back to Amazon for a replacement. The replacement arrived and it also appears problematic. The light reading is normal, but the temperature is 486 degrees F and the moisture is 1 percent. The device is stuck at these aberrant readings and they are obviously problematic. I've tried deleting the device and reinstalling several times. The result is the same.

Any advice or assistance would be appreciated.

Hello, 

My Netro has been watering despite heavy rains. The home page shows the soil is 100% saturated. Also, when I try to manually run the system, none of the zones will come on. I’ve tried the reset button and I’ve tried unplugging the system but it still won’t work. 

Any ideas? 

Rebekah 

I irrigation zones attaches to the same sensor. 

I do not understand why the smart schedule do not schedules the same amount of time, and dates for the 2 zones.

Best I can tell from the cursory technical specs is that for the Sprite the backup for a custom (not smart) watering schedule is in the cloud and for the Spark the backup is stored on-device in nonvolatile memory.  Is this correct?

My irrigation system runs off of a pump.  If I enable smart watering, will zones automatically enabled for a certain day run sequentially such that the pump will be turned on at the beginning of the daily cycle and off at the end of the cycle?  I don't want the pump cycling on and off multiple times during the day.

In the Netro app underwatering adjustment, what percentage setting is recommended under ‘moisture to skip watering’ and ‘moisture to add water’. I have a clay loam soil and we are having warm weather.

Why does the Spark controller schedule watering zones so erratically?  I have 7 zones and if it decides that all 7 zones need to be watered on the same day, why wouldn’t it just water in order 1-7.  Instead it might water 1,2,4,7,3,5,6,7?.  Or it might water zone 1-2 on one day, 4,5,6,3 the next day, and then 7,7 the next day.  

Just bought a home that has Netro however each time the sprinklers turn on they are pointing in different directions then we had them originally set. We end up watering cars and the street more than the lawn. Any suggestions? 

Hello

The system is stuck many times on watering, without showing a line below that is being watered. And so i have to restart it from the plug...

Any ideas? Can i restart from the mobile instead of plug?

I am trying to add a Manager and the system will not accept the email address I am entering. When I tried entering just a user name it populated an unknown email address. I deleted this. 

Then when I tried exiting the screen I received the Network Error 2507

I am still trying to figure out the rain prediction algorithm. 

I had 1 set of zones schedule to eater at 5 am on the 17th.

This was overridden by the program anticipating rain at 3am on the 18th (according to forcast). Why does it look so far ahead? Does it take into account the current moisture reading? There is an 85° full sun day between these events.

Hi, I need to use Only my programs but I cant turn off Smart control. So the app starts to water even When I dont want to. 

I recreantly purchased the netro controller and several times it has gone offline with having to unplug and restart. This seems to only work for a day and then goes offline again. I have rebooted my rooter which is on the same floor as the netro. Any help would be great.

Hello,

My Netro Sprite Is linked with the Google assistant and Google home app. I can see Netro in both apps but for some reason Google doesn’t accept any voice command or type commands. I tried many times resetting and reinstalling apps still doesn’t work,please help

Can I tell the smart watering app that it does not appear enough water is being applied to certain zones?