It’s like the app doesn’t know it’s connected 

To the correct WiFi although it is.  Bought a new sensor - not connecting since upgrade to iOS 13. Please advise. See pictures. 

Hi,

We have to take back inside our home the whisperer when the cold season is back I guess ? At what  exterior tempeture we should do this ?

Hi,

I have just replaced a Rain bird image 6 by the Netro Sprite and I am using it's power supply.

The problem is that once I connect it after first install it gets to solid white light. I press reset shortly or even for 8 seconds but nothing changes.

Can someone help me ?

Thank you.

You mentioned you would add the ability to display the ip address in the next upgrade. Having dealt with networking issues for many years. I find it best to be able to assign static ip addresses to my home networked devices so I don’t have random dhcp issues causes by laptops or phones reconnecting and trying to take over an IP address that might be in use by a device that is a permanent resident.

Would you add the ability to assign the IP address to the controller? Many people don’t realize the significance of this but I find it important to a healthy home network.

Hello everybody,

I own a Sprite and a Netatmo weather station. By now I have configured the Netro App to use Wunderground as the meteo provider. More specifically I have configured my own Netatmo Weather station as a provider. I have to say that it works pretty good in forecasting weather conditions. I would like to know if somebody else is using this configuration and owns also the rain gauge module. In case, does provide the correct rain amount of rainfall in the Netro app Discover page. It would be nice if the Netro "AI" could use the exact rainfall from the rain gauge provided through wunderground.

Anyone experimenting with this?

I only got my system delivered yesterday, so this could be something that I doing wrong, I have one whisperer in the back garden and one in the front. I live in Merida Yucatan and so it's hot all the time. The whisperer in the back is in direct sunlight most of the day yet it's reporting the temperature as 24. The one in the front is shaded by the house yet that is reporting 33. Both seem to be reporting incorrect moisture levels in both the topsoil and subsoil. Yucatán drains through stone to underground water sources so I would expect both topsoil and subsoil to be showing very arid.

Can anyone advise?

I’ve setup several schedules and in creating another new one, I run into errors about a schedule conflict.  I’ve disabled the other schedule so it won’t run but even then I get the error.

I would think that the app would be smart enough to not create a schedule conflict with a disabled schedule?

Is there a chance to swap the measurement units to km/h? 

Having a problem since upgrade of the app. Doesn't seem possible unless the main unit updated as well. Valves close within a few minutes of being activated by manual start, or programmed schedule. Have not test with smart watering disabled, but it happens on manual starts, so not sure that is even a variable. The Zone still shows as actively watering in the application. If you submit a stop  action by pressing the red square,then restart, via the sideways triangle, the zone will come back on again. However, it shortly shuts back off, while still showing the zone as being actively watered. This is happening across all four of my zones. Curiously, if you unplug the controller after the valve shuts off, but the app still shows it watering, wait a bit, and then plugit back int-the zone comes backon shortly after reboot.

Tested countless times, hasn't finished a cycle in a month. The zone stops sending the 24v signal causing the pump relay to snap shut and turn off the water supply, or perhaps the zone valve. Either way, appears to be a very odd defect. Do I need a replacement unit?  (BTW, I have all smart fumctioms disabled) 

I wasn't able to find a way to read the IP address assigned to the Sprite and/or Whisperer could you consider adding a page in the app where you can read the value?

Thank you,

Tony

I've been using my sprite with a Whisperer since a few months. The sprite works wonderfully but the whisperer has serious probloms. I get incorrect readings. Specifically my whisperer is stating 1% topsoil moisture level. Honestly this is impossible after a sprinkling succeded at 6:00 this morning. This misbehaving is going on since the first week. It works for the first day or two after resetting the whisperer but then it goes weird. On other occasions instead the topsoil moisture was stuck at 98% even after several days of not sprinling in full summer with temperatures over 35°. 

I have tried anything from resetting the whisperer to changing spot. At this point I'm led to think that the whisperer is broken.

Is anybody else having this strange behavior?

Do you have any other suggestion to solve this problem?

I have noticed that you are not giving due importance on support requests in this forum about whisperer problems. In my opinion you should put more effort into this.

https://netrohome.com/forum/posts/73/show_question

https://netrohome.com/forum/posts/132/show_question

https://netrohome.com/forum/posts/199/show_question

https://netrohome.com/forum/posts/289/show_question

https://netrohome.com/forum/posts/366/show_question

https://netrohome.com/forum/posts/392/show_question

Thank you

Good product but there is not a windows 10 APP or the possiblity to setup by browser directly to IP address of netro. There is not web server inside.

How can I adjust the manual run time for all zones?  They all seem to be different (one is one minute).

I recently ordered a second whisper and installed it the same way as the first one I received (which is still working fine)  It connects just fine and I can even change the color of the LED for a while.  But it reported only once to the app and that was it.  I have tried reconnecting it to WiFi, I even deleted it in the app and reinstalled it with no success.  After the initial connection it seems to just stop working.

How to determine prior watering schedule?

I have my controller in my garage here in the desert.  The transformer seems very hot to the touch.  Is this a problem??

My system says it watered yesterday, which it didn’t, and it’s telling me the next watering is in 8 days during my 100 degree days.  What’s going on?

It is unfortunatly not possible to change  in which ordre the watering will act.

for exemple I need to water zone 5 after zone 7 because zone 7 is at a higher level than the electro valve and remaining water pressure, after watering is stopped,  is to strong and prevents the valve to close . by watering supplemantary  zone 5 which is lower the pressure diminishes ans the valve of zone 7 closes..

I have a couple whisper sensors monitoring my lawn and drip system.   I understand how they can monitor the soil in my lawn but I’m wonder how the whisper works on my drip system as it doesn’t see the moisture that’s added to the soil(the emitter isolates the water to the plant) or the rate the plants use it like the one in the lawn does.  I’m assuming it’s just estimating like the Netro would on it’s own.  Is there much value to using a whisper on a drip zone?

What does the yellow triangle with the ! mean next to the schedule