Hi- it has been raining now for two weeks and it says moisture level 100% but still watering everyday?  

I have two whisperers, one in zone 2 at the front and one in zone 4 at the back. We're in Mexico so it's ridiculously hot and sunny all the time. The unit at the back faces north west. The unit at the front faces north. Both units are now dead. Neither will reset or power up. 

I can't add my wife to the system. Her email is first name.surname@domain.co.uk but the app says "invalid email" when I try to add her.

I would love to see a leak detector we could install onto the water lines that could communicate the amount of water used and detect leaks. Like the one Rachio offers.

Replacing old Toro system,  all my wires from the zones are too thick to place into the system.  Do you have a wire gauge I can slim down the wires to make it work?

I’m wondering how many whisperer units I need to have if I my garden has 8 zones. Do I have to get 1 per zone? 

Hello I bougth my first netro sprite but i can not find the country Uruguay and i the smart not work correctly, how i can resolve this issue?

So I have zones programmed to water at certain time on certain days... If I enable smart zone feature will it override the manual programmed setting or will the programmed settings still come on plus the smart zone feature.. Or do I have to remove /delete my programmed zones n just enable smart zone? 

This is an easy question 

Thanks

Hello Netro, will you have a black Friday offer? 

My sprinklers are starting 1 hr past when they are programed due to daylight savings ending.

I would have assumed the clocks changed with the clock on my phone but that doesn't seem to be the case. 

Haow can i change this? 

If your old controller has more than 12 zones, you will need to have 2 Netro controllers to replace it. Please follow the diagram below to safely wire the 2 controllers:

Now you can use the 2 C slots for the common wires and the 2 sets of 1-12 slots for the zone wires. If you do not have a master valve or pump, just ignore the orange wires.

IMPORTANT: the blue wire has to be connected to the left 24VAC on both controllers and the yellow wire has to be connected to the right 24VAC on both controllers.

Please contact us if you need the wire connectors shown in the picture.

Netro Inc

Hola,

No se si hay algún que hable español. Espero que si. 

Como programo el suelo si quiero poner tepes de césped?

Gracias

New system owner. When having fall blowout performed, I found I needed to be present to run each zone. I didn’t find a way to provide access to the technician. Other systems on the market provide this function. 

I am exploring different smart watering modes. The normal mode waters the lawn too long for me but the eco mode too little. It appears that the eco mode is exactly the same as normal but the watering time is half of normal.

In my case, I would like to set up a smart mode that waters 75% of the normal. How can I configure the smart mode to do that?

What is the best way to store the whisperer for the winter.  Should in keep it exposed to sunlight via a window.  Is there a way to turn it off?

I don’t understand why smart watering is planning to water my 6 zone area in different ways if they have all the same type of soil, sprinkle head, size, and species. 

OK. I have my plumber installing this. Unfortunately, this is México and so beyond the basics, most plumbers are struggling about in the dark. We've figured most of it out, but we're a bit in the dark on a couple of bits.

I have the following:

A ground source well with a Franklin Electric submersible pump as my water source. This pumps directly from the ground to the zone controller.

The zone controller is an Antelco EzyValve4 solenoid (https://antelco.com/us/products/valves/automatic/ezyvalve-4). This has a water input and four zone outputs. Each of the four solenoids has two wires and their website shows how to connect 1 of the wires together as the common and then the other four for each controller. This is all good.

The problem is power to the pump. The Netro installation video says "if you have a master valve, connect that to the M slot". I googled a bit and found "A master valve is an automatic valve that is installed at the point where the irrigation system connects to the water supply. (Sometimes this circuit is called a “pump start circuit”. Both types of circuits work identical, and can be used for a pump and/or a master valve.) The controller turns the master valve on and off."

So, does this mean I connect the power from the pump directly to the "M" slot? and would this then turn on the pump when a zone is opened for watering? So, Zone 1 comes on to water the garden, does this also switch the pump on?

From what I understand the pump will be 110v, so do I need a relay unit between the pump wire and the Neatro (24v)?

Can anyone give me a confirmation that this is the right way to configure it please?

Manually watering Zone 2, sprinklers stopped watering while the app still showing watering and counting the time, tried all other zones, none is watering though the app shows they’re. Checked wifi works, power to the controller works. The only thing I noticed is that the light on the controller is off all the time except when unplug and plug it back, the light flicks once and then remained off

After exposure >4 hours, the power button lights up red and shows no sign of connection. And one more detail is a Sprite capable of connecting with the Whisperer?

Pls answer me soon because I am in need of to use. 

Thanks