Hi!

How do I turn off the SMART SCHEDULE?

Thank's

I've been playing with my Netro controller for 6 hours now. I create programs and the first time when I look at the schedule the zones are not shown in order and then they repeat for a second time with a different intervals after the first run ends. I try cancelling the duplicates and both occurrences disappear. I could not figure how remove the duplicates only so I tried resetting the controller. I took about 5 tries before it worked.  Then I did the wifi setup and setup a new program. Just a basic 11 zones with a start at 6:00, weekly and start on jun 16,2022,and I enable it and save. When I check the schedule. Nothing shows up for 6/16 and on the home screen it says next run not scheduled.  All of the 11 zones say next in -- without any entry.

Can I program the spark to not water on Wednesdays. My lawn service comes on Wednesdays and I don't want them to mow a wet lawn.

my spark controller schedules insufficient watering of my lawn, so much so that it is very dry. on which settings (type of soil?) can I intervene to have longer irrigation times?

Thanks for your help.

It rained all day yesterday and will rain today. The app says it’s a thunderstorm today and to skip watering but I look outside and the system is watering the grass. How do I fix this?

I decided to skip all zones after the program started running since I am working in the yard today.  Three zones have run, but I want to skip the rest so it is not so wet. I get the following error. 

Is possibile turn off the withe light on the netro device?

Has anyone else noted that very few of these posted questions are getting answers? Is Netro even looking at these queries/problems?

I have a Whisperer that will not reset after winter storage.  No answers to my posted question. If I cannot reset the unit it will be the last one I ever buy. Only one season of function is unacceptable.

I was trying to see if there was a way to set a minimum moisture content for my grass. As in it can’t drop below 75% so that regardless of how much rain there is or Esther it had rabbits scheduled time or not it would run again or alert you that it needs watering?

My pixie battery has failed after 1 season of use.  It doesn’t hold its charge, and therefore the timer goes off line.  How do I get a new one?

Netro app says we received rain yesterday but it didn’t rain at all.  When I go to correct in app it only allows me to go as low as .1 inch.  How do I adjust to zero?

With the Pixie is there a way in app (and if so where) to see if it skipped a day because either the sensor reported that the soil moisture was above the threshold set or because the weather provider predicted enough rain to cancel it?

What does the  exclamation mark mean in the schedule pages?  Does this mean that they haven't run?? If so this is a major fail on the part of an irrigation system and should surely at the least result in notifications to the phone or email to alert?  I've had plants die in the last week of very dry weather as I assumed this was watering daily as per the advanced settings. s

I would LOVE to have a way to move a days scheduled run (and all subsequent runs) ahead XX days.  For example, if I have all my zones scheduled to run tomorrow, but it is raining today (and I'm scheduled for every third day runs), it would be great to move tomorrow's run ahead 2 days (as maybe it's not raining TOO hard, but enough to warrant not watering tomorrow), and then that move trigger all subsequent runs to move ahead by that many days as well.  Any plans for such a feature?

Hello.
Is it possible to move a Zone, in my case: "Prato e back giardino" from Terminal 2 to Terminal 3 in a efficient way?
Let's say, for instance:  Copy Zone "Prato e back giardino" or Move "Prato e back giardino" from Terminal2 to Terminal 3, without being obliged to cancel the previous and reprogram all in a new Zone?

I've a problem with Terminal 2: the wire broke inside and I am not able to remove it ....

Thanx a lot
Gian Piero

Sensor was removed thru winter. Now will not activate and shows single red light only. Been in direct sun for 3 days so fully charged. Cannot get white light to reprogram.

My rain delay is set to 15 days. How do I reset or delete the current delay?

The program is now scheduled 15 days out, and I have disabled and re-enabled my program in hopes it would reset it. I checked restrictions and the delay is not listed.

Thanks!

Trying to add ISANREMO24 to PWS but I always get this error:

Please enter a valid ID !

Can you fix the problem or add for me:

ISANREMO24

Weeper hoses need to run for hours, the only option in smart scheduling is drip irrigation which is having it max out at like 30 mins a day 

Just go to last page, standard UX