None of the zones are watering when the app says it's watering. I measured each zone when active and each read 28 AC. When testing the resistance, the readings were jumping all over the place for each reading. This is leading me to believe there is an issue with the master solenoid valve. However, there is no wire that connects to the M slot on the controller. Looking around the house for any of the underground boxes, I have not been able to find the master solenoid. Attaching pictures of what I have found. Any help greatly appreciated.

Hi there 

I have the garden zones like the diagram. And I want zone 4 a 3 run the same amount of time. Currently they use different whisperers and have different schedules what makes the grass to present in summer dry patches. I would like to force to run 3 and 4 the same amount of time.

Should I use only one whisperer attached to both zones (3 and 4)? 

Hello,

I have a number of zones that I would like to run for 180 minutes. Can you enable this for me?

Don

Everything shows it should be running, but it doesn’t wake up. I have it set for online during watering periods. It says it’s communicating but it’s not running. How do I wake up metro when I want to communicate

What is the significance of a red dot next to the green bell ? 

Do not see anything anywhere and have not received any notice.

Thanks

Is there a way to view all the input settings for a given zone, to wit, soil types, slopes, species, etc? It is difficult to check the data going screen by screen. Perhaps an Export or Summary capability I have not yet discovered?

Much of my non-lawn landscape area is sheltered by heavy tree canopy, meaning light rain does not reach the ground in the same amount that weather apps might report. If I find that smart zones are not getting enough water, how would I tweak the zone settings?

One day, the Sprite just stopped opening the zone valves. We tested and reconnected all the wires and deleted and re-installed the Sprite. Still no luck. Ground is good too. What could be wrong?

• 
  

Hello 

Just bought a Netro sprite-6 and a power adapter 600 ma but the sprinklers go up but not down, why? Could it be the amperage?

I exchange the power adapter for a 800 mA and i still have the same problem. 

If i do a manual irrigation and turn  it off in the middle it doesnt turn off,but if i tried once more to turn it on it turns it off....

Nuno

The smart schedule overlaps with the watering adjustment program that runs when the moisture goes below a %.

Yo can see here that zone 5 run 10 minutes the program and then 37 minutes the scheduler.  It has no sense and it is a waste of water.

1. After the watering adjustment run, the smart scheduler should recalibrate the timing based on the humidity of the land.
2. I have the whisperers, the whisperer should monitor the humidity and stop the smart watering once it reaches 99% of humidity but it seems the program runs all the way.

This could be improved in the application.

Thanks for your support and keep up the good job

En relación con mi pregunta anterior ya he visto que poniendo el riego nocturno a las 23:30 se acepta, pero si se pone a las 23:59 sale el error. Por lo tanto anulen mi anterior pregunta, aunque me resulta algo extraño que no permita 23:59 siendo el mismo día.

Saludos.

He instalado mi nuevo Netro Spark. En modo smart produce demasiados riegos en una determinada zona de forma muy constante, y con demasiado tiempo. No me parece nada lógico. Quiero dejar eliminado el modo smart y programar personalmente el riego. Consigo programar un riego de las cuatro zonas que utilizo en un determinado horario de la mañana, pero cuando voy a añadir un segundo riego diario por la noche me da un mensaje "ERROR: Program cannot cross a day".

¿Significa esto que solo puedo programar un riego al día? Muy extraño, mi anterior programador permitía tantos riegos diarios como quisiera simplemente indicando las horas.

Por favor, una solución, porque si solo se puede programar un riego al día no me soluciona nada este dispositivo.

Gracias.

Dear netro team,

I missing the function that I can open two zones at the same time.  If this is possible you could combine different valves.

This would be a huge advantage.

Thanks for your response. 

Hello,

Since 2 days now, my netro Sprite is offline.

The light is solid  but quickly blinks each 6 seconds.

What should I do?

Are Netro servers online?

Thank you,

David.

Where is the documentation on how to use the app? I have no clue how to set my own schedule or how to use the smart scheduling... I can't find anything on how to use this app at all and it's pretty confusing. I am looking at the app and it seems to have smart watering enabled, but there are times where it's skipping 3 days randomly and there is no rain that is supposed to take place on those days, so no clue why it's skipping those days. Can someone direct me to where the documentation is for using the app?  Thank you. 

Hi

i have a Netro app

on ios with a 12 station 

Starting this morning i receive a 

Network error message

i restarted/ re connect

same message

May i need a new firmware ? 

I noticed that Weather Flow PWS was added as a weather provider for Netro and successfully linked my Weather Flow Tempest with my Netro Pixie Z1+Hub+Whisperers.  However I have a few questions:

1) There seems to be no way to remove or change the link to Weatherflow, like selecting another station.  Can you add a way to do that?  

2) Since linking to Netro, I have changed the name of my Tempest Device on their platform from the default serial number to a descriptive name, but Netro still shows the old name for the device when I click on it in the Weather Provider menu, is that a problem, or are they still linked?  (and if it is a problem, how can I update the link?)

3) What data is actually pulled from Weatherflow?  The forecast shown in the Netro app does not line up exactly with what my tempest shows, nor do the rainfall totals on the discover tab.  

4) I have also linked my Tempest with Weather Underground and can use them as a Weather Provider instead.  The Netro app says Weatheflow PWS shares 9 days of forecast and 1 day of history, while Wunderground PWS shares 7 days of forecast and 7 days of history.  I prefer not relying on an additional middleman to link my tempest to Netro, but is it better to have the additional history or additional forecast?

Apparently there are times when the wifi connection to one of our Pixie devices is not reliable.  Yes, I should work on that.  However, it has worked flawlessly in the past, and this is something new.  Nonetheless, when the water schedule fails because of no wifi signal, there should be some kind of notifcation OTHER than having to open the app, go to the calendar, and look for the tiny red icon.  The app is right there on the phone, and could generate a notification.  The app has the email address and could generate a notification.  The current method is borderline dysfunctional, and mostly useless.

The main screen can say "Watered 10 hours ago"  .. but the calendar OBVIOUSLY shows that that even did not happen.

  

Hi!

What is the proper way for changing Whisperer from standalone mode to adding it to my Netro Pixie or Sprite?

Thanks!