Prior to installing a whisperer to my system, I set it up outside in direct sunlight for 5 days. When I try to add it to my Sprite, the light only blinks red once. I've tried multiple times to press the power button 6 times and it's still just flashing red just once. What am I doing wrong?

Hi I have ordered a Netro spark controller and three sensors. My next step is choosing 12VAC solenoids, a drip irrigation system for beds and pots and a misting system for my propagation bench.

I am new to this and would appreciate a pointer to recommended setups and suppliers.

Do I locate valves near to the Spark and run underground hoses to my beds or am I better off running cables to valves next to the beds? What are the pros and cons? 

Hi, 

For the moment, I have one whisperer connected to one pixie, and everything is working fine.

I have a question though, if I would add another pixie to control another watering zone, can I connect the same whisperer to that second pixie?

In other words, can I connect one whisperer to two pixies?

Thx,

JM

Hello-  I have two new whisper devices. Both will not go into pairing mode.  Press power button six times and the light just blinks red on and quickly off. Press three times and same thing.  

Hi

I have recently bought  a whisper sensor to complement my Netro watering system. I have a watering system in the garden, where Can I install the whisper in order to avoid it will be wet all days by the watering system? Do I have to put it outside of the garden? Thanks. Paul

Hi

I have recently bought  a whisper to complement my Netro watering system. It was bought from Amazon, but showed  no signs of life after following the instructions. I have left in the garden presuming it was flat. After a few day the unit is still showing a red light suggesting the battery is still not charged . Is the unit faulty?

Hello

Hi

I have to activate two zones at the same time but i dont know how to do It.

Thanks

why do i get this error? I am trying to install in israel

Basically, is the Pixie water control valve one way, or can it shut off/turn on with pressure from either side?  In order to install it so the button faces up, I need to install it so the water comes in what is labeled as the "Outlet" side.  I don't know if it's labeled "Outlet" because it is a male connection, or because it cares about the direction of the water.  Otherwise, I will need to buy a male/male and female/female adapter, flip it "upside down" and use it with the button facing down.

Thanks.

Hi,

my firmware version is the 1.1.1

Please, can I have the last firmware vesion and the instructions for update my controller.

The serial number is E4956E4B6B05

Thank you

Good morning

I have received two days ago my new sensor. I am not able to start the sensor to proceed with the installation.  

When I press the power button it makes a short flash in red after releasing but does not turn to white , blink or green.  

Same effect when I press quickly  three times or six times.   It only produces a short flash in red.  I can not proceed with the installation as my app does not find the Netro wifi of the sensor as it is off.    I tried to leave the sensor under solar exposure for a full day with no change in the behavior.  Still just a short red flash after pressing the power button but nothing else.

Can you guide me how to solve the problem? 

Below is a chart indicating the maximum wire runs that can be used when installing AC solenoids and valves.

22 AWG: 600 feet 

20 AWG: 700 feet 

18 AWG : 850 feet 

16 AWG: 1300 feet 

14 AWG: 2000 feet

Hi team.

I would like to know what is the maximun wire longitude that support by zone the Netro Driver using 24 VAC power supply.

Thank´s.

My sensor doesn’t blink white led. When I presses the power button, it shows solid white for a while and then green color and red and goes off. The instructions make me confused. I tried to press the power button for 6 times. What does restart 3 times means? My sensor never goes to blinking white color.

Dear support right now i am installing my new sensor connected with netro controller ( this is the first sensor) . I have 5 zone active but sensor is able to control just 3 zone is possibile to extend the sensor control  to a global of 5 zone for one sensor ? Thanks for your help .

I'm in the very fortunate position of having 2 homes - one in the UK and one in Spain. We've just had the garden reworked in the UK and I've been able to install an irrigation system controlled by a single Sprite controller. 

I'm very pleased with how this is working - and now want to upgrade the manual irrigation system we have in our Spanish house to a smart system. Can Netrohome / the (Android) app manage 2 different irrigation systems in 2 different locations (with 2 very different climates)?

Many thanks.

The unit is working good, yeah!  The way the wires get tab/push for contact is really cheap.  The "spring" of the contact is very , very loose.

Move the wire at all and no contact.  Then trouble shooting to find where trouble is.  Not a good design. Need a much more firm grip on the bare wire. something else or just poor quality?

can you please confirm sizes of water connection, I don't find on the website

Hola! Acabo de instalar mi Netro al sistema de riego. El el equipo antiguo tenía dos fases, pero ahora la instalación para que funcionara me obligaba a utilizar la celda “M” y me he quedado con una sola fase para todo el riego. Como lo puedo solucionar?