Just bought a home that has Netro however each time the sprinklers turn on they are pointing in different directions then we had them originally set. We end up watering cars and the street more than the lawn. Any suggestions? 

Why does the Spark controller schedule watering zones so erratically?  I have 7 zones and if it decides that all 7 zones need to be watered on the same day, why wouldn’t it just water in order 1-7.  Instead it might water 1,2,4,7,3,5,6,7?.  Or it might water zone 1-2 on one day, 4,5,6,3 the next day, and then 7,7 the next day.  

In the Netro app underwatering adjustment, what percentage setting is recommended under ‘moisture to skip watering’ and ‘moisture to add water’. I have a clay loam soil and we are having warm weather.

My irrigation system runs off of a pump.  If I enable smart watering, will zones automatically enabled for a certain day run sequentially such that the pump will be turned on at the beginning of the daily cycle and off at the end of the cycle?  I don't want the pump cycling on and off multiple times during the day.

Best I can tell from the cursory technical specs is that for the Sprite the backup for a custom (not smart) watering schedule is in the cloud and for the Spark the backup is stored on-device in nonvolatile memory.  Is this correct?

I irrigation zones attaches to the same sensor. 

I do not understand why the smart schedule do not schedules the same amount of time, and dates for the 2 zones.

Hello, 

My Netro has been watering despite heavy rains. The home page shows the soil is 100% saturated. Also, when I try to manually run the system, none of the zones will come on. I’ve tried the reset button and I’ve tried unplugging the system but it still won’t work. 

Any ideas? 

Rebekah 

I have one Whisperer up and running just fine. Based on this I purchased a second. The second produced readings that were inconsistent when the device was placed next to the first Whisperer (read about half on moisture when compared to the first). So, I sent it back to Amazon for a replacement. The replacement arrived and it also appears problematic. The light reading is normal, but the temperature is 486 degrees F and the moisture is 1 percent. The device is stuck at these aberrant readings and they are obviously problematic. I've tried deleting the device and reinstalling several times. The result is the same.

Any advice or assistance would be appreciated.

My phone will not connect to the Sprite, any suggestions?  It tells me to connect to Netro….., I select that in my WiFi options, but it does not connect.  

I have all connected and seems fine but when testing turning on each station I get a "pending" but no sction!

Each zone then said"loading"  for 5 minutes each then nothing. Please offer any help!

It's annoying that text overlap in the app. It's there a fix for this?

I'm only using a sprinkler system to water St. Augustine grass on a .2 acres in South Florida. The entire area is flat and has the same soil make-up (loam). Direct sunlight shines mostly all day on every area other than a small 10'x40' strip on the west side of the house that is shaded part of the day. I have no trees and no plants. I have a Sprite controller and 1 whisperer sensor which is connected to the 3 zones that get the most sunlight. The learned % is at 55%

I don't see any benefit in using the whisperer. Thoughts?

I have a whisperer and a pixie configured in the same zone. My pixie is defective (the unit leaks water which wound up damaging the unit and battery and no longer works, replacement is in progress), so I want to delete it in preparation for my replacement. It says I need to remove the sensor first. Is there any way to just move the sensor (a Whisperer) to a different zone, or perhaps to just simply unlink the sensor from the Pixie, or do I actually have to delete the sensor from my account and then go through the process of re-adding it back to my wifi network and all that? The app makes it seem like I have to actually delete it then re-add it. Since my replacement unit won't be here for over a week I had desired to keep the sensor monitoring the soil in case I need to manually water it.

Prior to installing a whisperer to my system, I set it up outside in direct sunlight for 5 days. When I try to add it to my Sprite, the light only blinks red once. I've tried multiple times to press the power button 6 times and it's still just flashing red just once. What am I doing wrong?

Dear all Netro customers,

The long waited new version (3.0.0) of the Netro app is on the horizon. The major improvements of this version are

1. faster in loading data 

2. new manual run interface

3. new home view design

4. more languages supported

We sincerely invite you to join the Beta testing program. Please email to support@netrohome.com or leave a message below if you would like to try the new app. Any feedback would be greatly appreciated !

Thanks,

Netro App Team

What is eating my marigolds 

I have 9 zones which water every even day. 2 of the zones (flower beds) also have separate program for odd days. When the forecast predicts rain on an odd day and it does not materialize I run the flower bed program in late evening. The problem is that the full program the next day skips the 2 flower bed zones. Why is this?

Can we also add a rain probability % as the inch/rainfall parameter is not shown in weather forecasts. How does the program know when measuring minimum rain restriction.

I have 9 zones which water every even day. 2 of the zones (flower beds) also have separate program for odd days. When the forecast predicts rain on an odd day and it does not materialize I run the flower bed program in late evening. The problem is that the full program the next day skips the 2 flower bed zones. Why is this?

Can we also add a rain probability % as the inch/rainfall parameter is not shown in weather forecasts. How does the program know when measuring minimum rain restriction.

I would find interesting to include in the new App version the statistics of the total time (minutes) of irrigation by day, month, zone, etc, for me it’s a more comparable data than the irrigation in cbm, I dont know exactly how it is calculated because you dont know the flow capacity of my system.

Hi I have ordered a Netro spark controller and three sensors. My next step is choosing 12VAC solenoids, a drip irrigation system for beds and pots and a misting system for my propagation bench.

I am new to this and would appreciate a pointer to recommended setups and suppliers.

Do I locate valves near to the Spark and run underground hoses to my beds or am I better off running cables to valves next to the beds? What are the pros and cons?