Each Smart Zone can be set to a preset, e.g. Frequent, Deep, Boost, EPA, etc.  If you click Customized, you can choose the Min and Max Soil Moisture, and the Flow Rate (inches/hour).  Presumably, there is a default value of these three choices for each of the presets.

How can I find out what the presets are for these three values?  e.g. for the EPA preset, what is the Min, Max, and Flow Rate?  Same question for all of the Smart Zone presets.

Thanks!

Ken

I want to turn watering off without deleting schedules.  I need to do some repairs

It rained yesterday yet my moisture sensors have not changed. How do you reset it or get it to measure correctly??

If I leave my sensor for a while it stops recording new data. The days where there is no data is recorded as a zero. This is obviously not correct.  Any plans on updating this?

Hi

Netro disconnect almost every day 

from wifi , without any reason(such as  Internet connection  missing / electricity black out ) 

I have to unplug and rebooting  it goes back automatically to wifi connection

What i have to do to avoid this ? 

I reset my netro sprite as work was being done on my sprinkler system.  It came back on slow blink.  I have not been able to reconnect to my internet.  when setting up netro shows up on my phone with good wifi connection, but will not connect. I have turned data off and still not luck. I have unplugged Netro sprite and still no luck. If anyone has any ideas please share.

What is the moisture range for St. Augustine grass ?

Tengo diseñados una serie de programas de riego.. ¿Como puedo insertarlos en el día en que quiero regar? P. ej. : día 21 de agosto quiero aplicar el programa "5"

Hola. 

Quería saber si este adaptador es válido 

We have 11 zones...I want to skip 1-3 and 7-8 an have them water every other day. I can't seem to figure it out! Unless I do it manually?

I have two controllers: a Sprite with 6 zones and a Pixie faucet controller.  I would like to use Google to start and stop watering on the Pixie faucet controller.  The User Guide FAQ says:

"3. What if I have multiple controllers?

Unfortunately, Google Assistant doesn't support multiple devices. The NetroHome action controls your first Netro controller. If you have multiple Netro irrigation controllers, please try with Google Home."

How do I control the PIxie in the Google Home app?

Will stop or keep looping the schedule?

I am confused. I have a program setup for zone 1-5 to start water starting at 9:00am on Tuesdays. I looked at the Home Screen today and it shows the next Watering for each zone to be like: Zone 1=8 Hours, Zone 2=11 Hours, Zone 3=11 Hours, Zone 4=7 Hours, Zone 5=8 Hours. 

It’s 10:30pm on Monday night now. Why are the times shown different? I want Zone 1 to start at 9:00, Zone 2 to start when Zone 1 finishes, Zone 3 when Zone 2 finishes... why are these times all over the map?

For some reason the pixie is stuck in the on position. I cant turn off the water 

Dear Netro,

Although you have provided a lot of data via the api. And for all of you who wanted to get data out to your smart hub, it's there for the grabs ! 

ONE DOWNSIDE, i would have expected the battery data of the plant sensor to be provided for the start and potentially the state of the sensor. Although that you could potentially use the last update, to deduct this. When can we expect this to get updated ? 

Buenos días hace una semana que instalé Netro 12  estaciones

He perdido la señal wifi en tres ocasiones. He observado que para que vuelva a estar en línea debo desconectar de la corriente eléctrica y volver a conectar el programador,. Me gustaría saber si esta es la manera normal de proceder.

Por otro lado también he observado que si esta fuera de Línea, no riega el jardín lo  que  supone  un problema, pues el programador no lo tengo en mi vivienda habitual.

De que manera puedo resolver estos dos problemas.

Un saludo

Although that I'm still hoping Netro will start understanding their appliance/app is only a smart part of a smart home ecosystem and start integrating with Home Assistant. Even huge vendors like Tuya, have understood that this is essential for most Home Automation Enthusiast. 

For the time being, some folks have used the API to get some data to home assistant https://community.home-assistant.io/t/netro-integration/51012/13

I believe a lot of us are happy with the appliance, but aren't looking at it often enough. Result in my case at least that my whisperer was out for more than a month. This could have been avoided if we had an integration to Home Assistant who would have alerted me.

So please Netro, do the extra mile !

We had 1/2” of rain this afternoon and the scheduled watering came on tonight. Is there an easy way to stop watering all zones for that day?

Hi,

I have a whisperer that monitors zones 1, 2, and 3.  Zone 1 is the primary zone.  Because whisperer detected a moisture level that was too low it did an additional watering of 10 minutes.  The strange thing about it is that it only watered zone 1 for the additional 10 minutes.  Why didn't it water zone 2 and 3 when they have the exact same conditions and moisture levels.  I had to go in and do a manual run to even out zones 2 and 3 with zone 1.  

Also in the beta software when you try to switch from basic to advance watering or choose a different watering algorithm you get an error message.  

For some reason my controller goes offline every once in a while. It messed things up because it shows all of my zones are underwatered when I’m reality they have been watered. Is there a way to switch it from one with network to a different one that is closer. I can’t seem to find how to update the wireless network for the controller