Why or how does the rain delay option work?

Mine is set up with the minimum rain but the program still goes off no matter what. 

My B-hyve sends me a “rain delay” message. 

How can I adjust the flow rate of my system?

I have a whisperer in one of my zones connected perfectly. I have a large back yard, so 3 of my zones are essentially the same. No difference zone-to-zone on the sunlight, slope, grass type, soil type, etc...

Can I have multiple zones use that one whisperer for data? I like the soil moisture readings from the sensor (currently sensor zone shows 33% moisture but the other two zones without the whisperer show 65% moisture).

Thank you!

I notice that the IFTTT apps are pre canned. I have 3 whisperers and would like to control 3 different zones. I got around this by choosing a to water when moisture fell below 40% and 50% for 2 different zones. I there a way to trigger 3 different zones at the same 40% moisture?

Again Thanks for your efforts.

The Netro service is now live and available for all IFTTT users! Please download the IFTTT app on your phone or use the official IFTTT website to connect Netro with other smart devices or services. For more information, please visit the following webpage: https://ifttt.com/netro

In case you experience difficulties in using the Netro service on IFTTT, please write to support@netrohome.com or contact us in the Netro app.   

Thanks,  

Netro Inc

Last summer I used Smart Zone Regular mode.  It did a great job but it watered somewhat more than I would have liked.  I checked all the other mode settings and outside of ECO which looked to cut it in half I didn't see any mode that would do what I am looking for.  For customized I didn't see a clear way to have it water say 20% less than Regular mode.  Is there a straightforward ways to do this?   Seems like a nice feature would be to be able to adjust a mode up or down in say 5% increments or so.  That way we would have all Smart Zone Advanced benefits without having to do a lot of manual customization.   thanks

La salida eléctrica es a 24v?. Podría conectarlo a la electroválvula Rain Bird?. SI quisiera controlar otros dispositivos como bombillas de 12/24 V AC, en distintas zona Puedo hacer? Puedo hacerlo de manera manual o programando por horas, sin interferir en el riesgo?

Hello,

I am upgrading from 6 to 12 zones controller.

Is there a way to move all the historical data and zone settings to the new device ?

Thank you

When I turn on manually by pressing two times it’s fine. However the water turns off automatically after a minute or two. Is this right?  How do I get it to stay on longer so I can shut it off manually 

Also should the LED stay on all the time?

Hi, 

Could we get a notes section in the zone setup so we can record extra information about the zone.  it could be wire colouring for install, notes about other setup / sprinkler install information or general notes about how that zone is performing and changes we might want to make.  

Thanks

Can I have your help with Metrosideros (Myrtaceae) please ? I can't find It in the plants Mame in the Netro App. Sun? Water? Can you suggest me a similar one in the Netro App?

Thanks a lot,

Ale

I am new to gardening and traditionally, I can kill a plastic plant.  I have started a small flower bed with 3 rose plants in it.  

Is there a way to read the information in the app to learn how many gallons have been given to the plants in a given period of time?

My simplistic understanding of the rose plants is they should get 3 gallons a week total.  My current moisture % in the app shows 68.  Do i need to focus on getting that and keeping it at 100%?

Thanks ahead of time for any education you offer.

Todd in Texas

valvole hunter 24vac, netro non apre le valvole.

i collegamenti sono stati eseguiti come da istruzioni.

Quale può essere il problema?

Alimentatore 24v 1000ma e’ corretto?

I have a whisper installed and was wondering if the setting "Moisture to Skip Watering" is based on topsoil or subsoil moisture.

Is there any plan to allow for Smart things compatibility on the Netro units?

This season when I put my whisperer back out to monitor my garden bed I looked on the app and no longer saw that device. So I went through the process to re-add it to my network and my Netro account and I get an error message stating that that serial number is already registered.  Anyone have any thoughts on how I can de-register and re-register this device?  Thanks

For the last week all the watering events in my calendar show an exclamation warnings symbol. But I have no way of knowing what that means. I have no alerts from the system. My grass looks like it's dying. What is going on? 

How do I reset all the programs in the watering schedule and clean up the calendar ? 

Can a pump delay be programmed between zones?

Thanks