I do not understand how many millimeters to set. I have microsprinklers of 4lt/h and 2lt/h. I thought to set to 4000ml/h but the max is 100ml/h.

How to calculate? I have a big terrace with 30 plants and various microsprinklers.

Thank you,

Vieri

Hi, I'd like to reduce the watering time in 1 zone which gets dumped each time Netro waters. The other zones are ok. Is there a way to do that in the smart mode? Maybe set an offset for that specific zone?

I have a Sprite with 3 Whisperers, all in the veggie patch.

I have the zones set to customize with a low of 25% and a high of 45% (I find 30 - 35 % moisture about right)

But the zones just won't get watered!

Zone 1 is down to 6% today and has been dropping steadily for days.

I HAVE to manually water, as the day time temperatures are consistently over 30 degrees (today 33, tomorrow 37).

Otherwise the plants will die.

Given there are only two values to enter (low and high). How do I stop the Netro from skipping days and putting the zones in the "Moisture" category??

At the end of the whisperer's learning time, the times are set automatically in the program or have to be done manually?

My main water line to the sprinkler system came loose and flooded my vacation home yard with 250,000 gallons of water before the leak was discovered and repaired.  Does Netro have the ability to control an electric valve on this feeder line such that the main valve will only open when the irrigation system calls for water?

My flower gardens have several inches of wood chip mulch covering the soil.  After a season of "Smart Watering" my beds are dry and the perennial plants are stressed.

Does mulch absorb irrigation water intended for the plants?  Is the presence of mulch a factor affecting the duration of an irrigation cycle?

Because it rained for two days, I put temporary restrictions on programming my Netro. Now I cannot reprogram it no matter what I do! Any clue what I should do besides the manual or adding new program?

Hello,

I was wondering if it's possible and makes sense to connect more than one rain sensor to the Netro Sprite.

I do not know if it happened before, I noticed it today with yesterday's irrigations.

The report from the Netro app (iOS) says that 2 of the 5 planned waterings failed (BTW, why , for which technical reason ?)

The report from the web interface says that 3 of the 5 planned waterings failed (BTW , why, same question above)

I set up a IFTTT applet to receive a notification after every successful watering and according to that 5 to 5 waterings were OK.

I do not post screenshots from IFTT as they are 5, but of course they are available for digging if anybody from netro needs them.

Please help me:

1.  what should I trust ?
2. based on which  result (app or web) did the scheduler react for today's waterings ? I suppose on web, because I got today exactly the three waterings that "failed" yesterday according to web report.

Thank you.

APP:

WEB:

Is there a published list online of Wunderground station IDs supported by Netro? Specifically, I'm looking for Hawk Ridge - KCOCOLOR1090

Thanks!

I have a netro sprite.  I live in Dallas.  My lawn as drought tolerant bermuda grass.  The grass can easily get by with 10 minutes of watering once a week.  When I look at the logs I see that the sprite is watering the each zone 5 to 15 minutes a day.  I enabled water regulations which  restricted water to Wednesday and Saturday.  Even with this change, the schedule still says 14 to 18 minutes of watering for each zone on the watering days.  I do not have a whisperer

My settings :

grass type:: warm season grass

soil type: clay

sprinkler type: rotor head

shade: none or some shade

smart zone: enabled (Level=advance, mode=eco)

area = 1000 sq ft (I tried reducing this value but then the estimates under "smart zone" go to zero)

Can the pixie faucet timer measure flow rate or amount of water dispensed?

Was looking at the smart water schedule this AM and noticed an exclamation points next to several some start times. What does this mean?

I always read that it was better to water early in the morning than in the evening. I see Netro gives the option of 2 frames daily though.  I turned on two frames and created a lengthy frame in the morning and evening for watering. Now when Netro schedules my watering it breaks it up between the two zones - even though the morning zone is long enough to hold the entire watering schedule for any partucular day - so presumably Netro thinks it's better to do half the watering in the morning and half in the evening.  My question is "What is the best practice with Netro watering, and why does it choose to water morning and evening rather than just morning? ". I was sort of expecting it would only use the second frame if the first frame wasn't long enough - but this is not the case.

Please add the Weather Underground stations:  KCAMENIF47 and KCAMENIF19 to the app as available weather stations.  I'm still getting the error code 'Please enter a valid station ID" when trying to utilize either of these weather stations.  Thank you.  

I have areas of the lawn that are consistently brown during the summer. I bought a whisperer to tell sprite to correct itself but it doesnt seem to do that. If the soil moisture that is estimated by the Netro app is incorrect, why doesnt the whisperer update the algorithm? Example: I have tried to set the soil moisture to 80% low to 100% high.  The grass on the customers property is brown and they are not happy. When I check the app, The whisperer says that the soil moisture is 63% but the app says that the next watering is scheduled for 22 hours? It also needs to be able to keep a greatly increased watering schedule until it corrects the problem. It is getting hard to work with this. 

The app seems to work fine when there is natural rainfall and the lawns look green. When the stress of the summer arrives, the customers ALWAYS complain that there is not enough water on some zones. The boost feature is not sufficient. there needs to be a way for us to increase the amount of water that is applied without having to make a manual schedule. That would defeat the purpose of using Netro. There needs to be a way for the user to correct the algorithm. The app will say that there should be 80% soil moisture but when I use a moisture meter and take a direct reading the moisture is around 30%. 

Hi. 

I've got my Netro Sprite with 10 zones configured. All of them with the smart watering feature. And 8 of them with he ECO program. It seems that my unit is overwatering. When I check the calendar most of the zones are watered twice and if I skip some of the zones both events dissapear and the whole time is filled with more instances is the non slipped zones. 

I've configured the watering time from 7:00 to 9:00 and some days it covers the whole time and others it covers from 6:00 to 9:00. 

Any ideas to solve it?. 

Thank you very much. 

Hi there, 

I'm currently using the smart watering feature on all my zones. However, I have a few zones with turf that are on a slope. It seems like the smart watering feature uses long duration watering sets (more than 25 minutes) that's causing unwanted runoff. Also, since I'm on a well, the longer irrigation sets really taxes my water pressure. My pressure drops after 13 minutes or so making the spray pattern uneavenly distributed with less water and also changing the application rates. Having shorter duration irrigation would help my well recharge and maintain pressure during the irrigation.  Is there a way to minimize the duration or set a max duration irrigation setting for a group of zones so I don't continue sending water down the road? Ideally, having many shorter sets rather than one long set would be helpful, a cycle and soak approach. Thank you! 

I am a Rachio guy but love the sensors by Netro. I’m trying to figure out how to set my watering recommendations from Netro with Rachio. What I’m lacking is ability to set my zones up and amount of water flow from different head types. How can I do this with Netro?