Right now the watering schedule the Netro program is using for my St. Augustine grass is killing my grass. I live in Dallas and Jully/August is brutal on lawns. If I water outside the schedule the program has established the schedule is changed. Is there anyway for me to water my with Netro and keep the smart watering schedule Netro has? Right now I by pass the Netro by manually engaging my water values, not using Netro. 

Thanks,

Will

I had to turn off my water valve to my sprinkler system for a week (ending in a few days) and forgot to disable smart watering on my netro.  Netro thinks it did a complete watering last Saturday, and adjusted estimated soil moisture accordingly.  Netro isn't planning another watering for another 9-10 days.  However no watering last Saturday occurred.  

How best should I handle this?  Is there a way to delete past watering, which will lower soil estimated moisture, triggering a sooner watering than currently scheduled?  Or should I just do a manual long watering as soon as I can?

I have an issue/conflict  with the watering adjustments for the sensors and the Smart Zone Sheduling

I have seen something weird. 

• I Have set up the Watering Adjustment for sensors the following I describe o be sure about the problem
• Moisture to Skip watering 50%
• Moisture to Add watering 30%
• Duration 5 minutes (only) -- it is a check

• The Smart Zones are st up the following
• Smart Zone - enabled
• Mode - regular

The watering run today only 5 minutes, when the smart  schedule  defined by the system was above that. As you can see, tomorrow watering says different time runs per zone, but it will run a maximum of 5 minutes. This means that the sensor configuration overrides the Smart Zone. And it should not.

As far as I understand the Watering adjustemt is to add EXTRA watering when needed based on the moisture level. Attached picture

Prior to this setup I had the Duration for Watering Adjustment for 15  and 10 minutes, and you can see in the past days runs, that always run for 15 -10 minutes depending the zone/sensor. - Attached picture

In previous weeks, it was working fine and adding extra watering when need it to keep the moisture levels.

Any idea?

I DID THE CHANGES PROPOSED BY NETRO  and it is not working

Take a look the screen shots

Zones 3,4,5 it is below the 30% trigger

Ciao.

Just installed Netro Sprite.

I enjoyed to set up the zones with advanced Smart watering, but I'm not confident with what is reported in "estimated frequency and duration". The frequency showed in the setting page seems too long (e.g. every 6 days)... but, if I see what is scheduled in the calendar it seems much closer to my expectation (e.g. every 2 days).   How daoes it work??

Thanks

Maurizio

Hello.

I installed my netro yesterday and now after watering all zones it shows me that the next watering will be in 5 days. It seems to be to far away in the future since it's 35 degrees celsius and sunny all day

Hi,

I have anabled the smart watering for my netro.

I have 4 zones activated.

My question is why netro water big areas only for 1 or 2 min and the small areas for 5 mins. 

I have done all the settings(sun, shade, soil tile, grass tile, area in sqm). 

Please help. 

Thank you

Hey, I'm a techie and I have a question about your "smart watering". What is the feedback loop that you use?

My zones are vastly different -- some have very small spray heads, and some have very large rotors that pump out a lot of water. At first glance, I cannot see any way to (a) indicate how much water is delivered per zone or (b) indicate how moist the soil actually is.

Assuming that I have not missed anything, I have a few suggestions:

1. Provide a mechanism for indicating the water deliver rate for each zone
2. Provide a mechanism for manually imputing the actual, measured moisture of the soil
3. Provide a "hint" mechanism for each gone (e.g. "This zone is too dry" / "this zone is too wet") which would in tyrn influence the smart watering.

I need the Netro system to water every day in this hot, dry climate. Our lawn is turning brown. It’s used to being watered every day. The smart watering system is watering every 4 days. I have both the frequency set to high and the moisture levels set to high. I do not have sensors. What else can I adjust to get it to run every day. I’m trying to figure out how to choose everyday using the smart system. Do I just need to set manual program? That kind of defeats the purpose of having smart watering (adjusting for rain, etc.)

Thank you for any help!!

Hi,

If you are using the “basic” smart watering mode, is Whisperer data considered to turn off a watering schedule similar to what is done with the weather forecast?

Thanks,

Andy

Does smart zone adjust water time depending on temperature change?

For instance, does smart zone automatically adjust to water more for those days over 90 degrees and water less for cooler days?

I have a whisperer in one of my zones connected perfectly. I have a large back yard, so 3 of my zones are essentially the same. No difference zone-to-zone on the sunlight, slope, grass type, soil type, etc...

Can I have multiple zones use that one whisperer for data? I like the soil moisture readings from the sensor (currently sensor zone shows 33% moisture but the other two zones without the whisperer show 65% moisture).

Thank you!