Dear Vanina,

Please check the wires. Are they loose or disconnected from the slots? Please also check the common wires and the master valve if you have one. If you believe the wires are correctly installed,  please check if there is a main valve/faucet that is turned off manually. 

To test if the controller is working properly, use a multimeter (AC voltage mode) to test the voltage between the common wire and the zone wire when the zone is active. Normally the voltage should be between 24V and 28V.

You might also want to check whether there are shorted zones or open zones. You just need to use a multimeter to measure the resistance between the common wire and each zone (remove the wires from the slots before testing the resistance). The normal reading would be 20-60 Ohms. If the reading is less than 10 Ohms then you might have a shorted circuit in the solenoid and if it is larger than 80 Ohms you might have an open circuit. 

Thanks,

Wency

Netro Support

Hi Duane,

Could you please send us email to support@netrohome.com with your Netro account registered email?

We will have our technician look into this issue. 

Thanks

Wency

Netro Support

Hi Jose,

It is the battey issue. Could you please place the sensor under the sunlight for another 2-3 days to charge it up and see if it works?

Thanks,

Wency

Netro Support

Dear Quim,

The red flash means the unit has less than 10% power. The winter sunlight may not be very strong. 

Could you please place the sensor under the sunlight for another 2-3 days to charge it up? Also, Do you have an incandescent lamp at home? If so, you can try to put the sensor under the incandescent lamp for 24-48 hours and it may come back to work.

Thanks,

Wency

Netro Support

Hi Vieri,

Thanks for your suggestion and I will forward it to our R&D.

Thanks,

Wency

Netro Support

Hi August,

I will forward your request to our R&D. Netro also supports IFTTT and you can find more information about IFTTT here: https://www.netrohome.com/shop/user_guides/6

Thanks,

Wency

Netro Support

Dear customer,

Netro allows one sensor to monitor up to 3 zones and you need to make sure the zones have similar environmental conditions. Please go to Settings->Sensors, select a sensor, go to Zones and select the zones you would like to monitor.

Thanks,

Netro Support

Dear customer,

Your device is in ilde mode so it cannot reschedule now. please go to the home page, toggle the "enabled" button to enable your device.

Thanks,

Netro Support

Hi Marcos,

Could you please send us email to support@netrohome.com with your Netro account registered email?

Hi Helidoro,

The defalut unit is Mps. If you want to use Km/h, the unit can be set to km/h in settings->account->unit->SI-w. 

Thanks,

Netro Support

Hi Wessam,

Thanks,

Wency

Hi Helidoro,

Do you see the loading icon if you start manual run from the Home page? Could you please send us the screenshot of the loading icon to support@netrohome.com? 

Thanks,

Netro Support

We have fixed this issue now.

Hi Jamie,

We have fixed this issue and could you please login your account to see if it works now?

Thanks,

Netro Support

Hi Jamie,

Our R&D are looking into this issue and we will get back to you soon.

Thanks,

Netro Support

Hi Mick,

Could you please send us email to support@netrohome.com with your Netro account registered email?

 Hi Jamie,

Could you try to uninstall the Netro app and reinstall to see if it helps?

Thanks,

Netro Support

Dear customer,

You can try the beta version of v3.0.1 on Google play and join the tester program to see if the issue has been fixed. The 3.0.1 android app can only be accessible when you join the Beta tester program on Google play. We will also launch the official 3.0.1 this week and you should be able to use it as a regular user too.

Thanks,

Netro Support

Hi Ben,

Netro sever side gets/updates weather information every early morning at 4 am. If the default weather provider doesn't work for you, you could try other weather source in settings->controller->weather provider. Please let us know if it works.

Thanks,

Netro Support